Veneer

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Macassar Ebony Elevator Panels

2/24/19       
Y.heller

Hey guys,

I am bidding on a job that I was approached on to supply Macassar Ebony panels for a retrofit for 2 matching elevator cars.

I have specified FR Flake as the core material.

As it stands my estimate is specifying ME for the back side and the face.

I was wondering if there is a suitable wood species to veneer the backside with that is cheaper as it will never be seen in order to tighten up the price point for the panels.

It will have to be the same thickness of course, but I worry about the density of what that species is and the MC%. I was looking for wood types that are within a 10% density range or less of the Macassar.

My experience tells me not to do it and if they want ME on the face, they're getting it on the back side also from the same log.

Have any of you guys ever tried balancing the sheet with two different woods that are close in density? What were the results? Did they end up cupping/warping out?

2/25/19       #2: Macassar Ebony Elevator Panels ...
Tom Gardiner

As a matter of fact I have pressed Macassar ebony on FR Pcore with a cherry reject back for elevator cabs! (hey quit mowing my lawn)! :)
I didn't have any problems with the panels staying flat. If you are working with FR board be aware that it reacts with PVA in funky ways. I was cold pressing and I had to extend the press time by another 30 minutes. Do a test! My feeling is that most warping issues are caused in the hours immediately after pressing. Balance the panel's exposure front and back. Support them on a level flat surface etc

2/26/19       #3: Macassar Ebony Elevator Panels ...
Charles Wright  Member

Website: http://www.northcreekwoodworks.com

We have done a lot of Macassar panels. We use maple when the panels do not require Ebony. Similar density stiffness etc.
If you are using plain sliced face use the same on the back; same goes for qrt cut, match the cut on the back. I would also suggest hot pressing if you can, it will set the glue up before it is absorbed by the core. As TG suggests, do a test.

2/28/19       #4: Macassar Ebony Elevator Panels ...
Y.heller Member

Hey guys,

Interesting. That cuts my bid price considerably into what I felt was more reasonable for the work.

If I get the gig I will be pressing in the Hofer 5 x 10 top/bottom heated press.

I was planning to use Urea Formaldehyde Resin at about 120-130 degrees.

I have never actually pressed macassar ebony as of yet. I am curious to see if I get grain saturation with the rigid glue.

I will need to make up approval samples anyhow so I was planning to try it at 120-130 degrees and another at 190 to liquify the resin.

In your experience do you guys wipe the sheets with acetone or similar prior to gluing down to drive out some of the oils?

2/28/19       #5: Macassar Ebony Elevator Panels ...
John Van Brussel

Website: http://www.veneersystems.com

I have heard conflicting opinions on wiping with acetone. Some say it just brings fresh oils to the surface.

2/28/19       #6: Macassar Ebony Elevator Panels ...
David R Sochar Member

I have come to believe that water base glues are better with dry, non-oily woods, and solvent based glues are better with oily woods. And TB III is good for just about nothing.

2/28/19       #7: Macassar Ebony Elevator Panels ...
Tom Gardiner

I'm in the no wipe camp for ebony. I have hot pressed with UF and PVA, cold with PVA and had no adhesion issues either way.

3/1/19       #8: Macassar Ebony Elevator Panels ...
Y. Heller Member

Right on. My gut feeling on the approach was to just run the veneers dry with no acetone spray/wipe.

It's .5mm veneer, I was thinking the UF from Spectrum should saturate the grain.

The samples I'm pressing in the next few days will tell.

And agreed... More and more I am staying away from aliphatic glues. I no longer even consider using it for veneering anything.

With laminates I use PVA glue. To hell with contact cement.

As far as a lot of the woodwork, I've started to just use UF for assembly. Doors, stave cores, counter top edges, panel glue ups, etc, etc. With flat panels and doors I find it's not that bad in terms of wait time because I just throw everything in the press and use the heated plates to kick the glue. And everything comes out dead flat which is nice.

This just occurred to me...

Have any of you guys tried polyurethane glue for veneering?

I recently veneered a table top with two layers of 1.5mm QS cherry using polyurethane glue from Spectrum.

It worked really well for that project due to our inability to calibrate the core prior to veneering. The top was too wide for our sander. We calibrated the 1.5mm veneer first and taped the cross band and face sheets together. In order to negate any inaccuracies in the flatness, we relied on the Polyurethane's glue line expansion to fill those defects.

I'll add that to the list for samples with the Macassar and see how it turns out.

I appreciate the advice and wisdom gents!

3/1/19       #9: Macassar Ebony Elevator Panels ...
Tom Gardiner

Something to think about with PU glue - when the glue foams into a gap it has little to no bond strength. I would prefer a depression in the face that can be sanded back to an unstable pocket beneath the veneer.

3/4/19       #10: Macassar Ebony Elevator Panels ...
David R Sochar Member

Regarding veneering with poly glue - I have been there.....
We vacuum bagged a walnut job with "The Black Hand" glue, and had more bubbles than Sally Rand. Trouble was, there was so much glue that it accumulated and then swelled as it came out of the press and cured. Once swelled and cured, it was trash.
Since then, we have found that clamping single faces with perfect cauls will put it down well. Lots of pressure from handscrews, etc. Toothed spreaders used to spread the glue.

3/4/19       #11: Macassar Ebony Elevator Panels ...
Y. Heller Member

I hear you on using polyurethane glue in a bag being a pain.

I use it only in the Hofer veneer press for those very reasons. The glue expands and spreads out to the edges of the panel which gets cut off anyhow.

In a veneer bag this makes one hell of a mess without the proper precautions in place.

However, the glue simply can not move the platens of the hydraulic press and we typically run somewhere around 60-80lbs per square inch.

The cherry table top that I tried this on came out perfectly.

My only issue with it is if there is glue squeeze out at the leaf seams. While the press keeps it super flat and it dries as a thin film on the surface of the veneer, it is much harder than the wood.

This was fine on 1.5mm veneer that I could sand those harder spots down and then evenly sand the entire top. I checked it with a precision straight edge as I went to make sure of flatness, but this is not going to work with .5mm veneer. I'll burn right through it.

I think it's going to be Urea on this one.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)