Your search for kilns found 824 documents (of 3711 searched).
1-824 of the 824 results are displayed below.
Forum Message Results:
Advanced Lumber Drying Workshop A message posted at WOODWEB's Sawing and Drying Forum (5/25) -- This is a reminder that Penn State Extension will be hosting an Advanced Lumber Dryin ...
Advanced Lumber Drying A message posted at WOODWEB's Sawing and Drying Forum (4/23) -- Penn State Extension will be hosting an Advanced Lumber Drying course on June 28, 201 ...
Equipment selection on dry kiln for wood A message posted at WOODWEB's Sawing and Drying Forum (5/17/22) -- This question is for either Professor Wengardt or others that have expert advice r ...
new dry kiln on the cheap A message posted at WOODWEB's Sawing and Drying Forum (12/11) -- Howdy all, i will see if i can get some photos off my phone onto here so you can all ...
Re: secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/9) -- Doug, Your retirement idea is indeed a good one, BUT... You will get more income and m ...
Mini Kiln questions A message posted at WOODWEB's Sawing and Drying Forum (7/19) -- I just built a mini version of a VA tech solar kiln (4’ x 2.5’ by 2.5’ ). I did it co ...
Re: kiln drying sinker Caribbean heart pine A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- Hi Gene,..thanks for your response and questions. We will be initially drying 4/4 wit ...
VT Solar Kiln Workshop 2019 A message posted at WOODWEB's Sawing and Drying Forum (3/27) -- Drying Lumber with a Solar Kiln We will hold a two day program on drying lumber with ...
Solar kiln - questions regarding first drying run A message posted at WOODWEB's Sawing and Drying Forum (5/26) -- Am going to be starting up a solar kiln for the first time in a week or two, and have ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/14/22) -- I built an electric kiln in my wood storage shed. I use it to KD wood that I first ...
Re: solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/13) -- In the U.S., wood and natural gas energy is so inexpensive that it is hard to justify ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- I am not that familiar with Solar Kilns. Perhaps someone else that has experience wit ...
1/2 Day Solar Kiln Course A message posted at WOODWEB's Sawing and Drying Forum (3/27/26) -- 1/2 VT Solar Kiln Course Location: Expo Richmond, Richmond VA When: April 16th, 9: ...
Solar kilns and cold cloudy days A message posted at WOODWEB's Sawing and Drying Forum (11/29) -- I've got a Virginia Tech design solar kiln operating along the PA/NY border. This su ...
Maintaining heat, and program settings A message posted at WOODWEB's Sawing and Drying Forum (8/20) -- Hello all wood enthusiasts ! I am hoping you can help me as I am new to wood drying a ...
controlling the humidity in kilns A message posted at WOODWEB's Sawing and Drying Forum (2/7) -- I have been operating the kilns for about a year. this past winter I have noticed the ...
Solar Kiln - Ash drying questions A message posted at WOODWEB's Sawing and Drying Forum (2/24) -- A couple of questions about drying ash in a Virginia Tech design solar kiln The VT pu ...
Solar Kiln pile placement question A message posted at WOODWEB's Sawing and Drying Forum (2/11) -- Hoping Dr. Gene will weigh in here with an opinion. If a Virginia Tech type solar kil ...
Re: Solar Kiln from Storm Smashed Greenhouse A message posted at WOODWEB's Sawing and Drying Forum (12/5) -- It has been up for about a month now. The temp inside the kiln goes to about 50-60ºF ...
Maintaining wet bulb temp A message posted at WOODWEB's Sawing and Drying Forum (5/31) -- I have just recently built a kiln and use the Nyle 53 dryer along with the power vent ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (2/21) -- I have to disagree with response #11 by Chris, who gives a link to swimming pools. Ki ...
Re: when can we use white oak? A message posted at WOODWEB's Sawing and Drying Forum (12/18) -- I agree with Tenn. that the QS white oak could be dried from green in the kiln, but ...
Kiln Newbie A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- I have spend hours on the forum reading, so I apologize if this was discussed somewhe ...
DH kiln drying douglas fir beams and posts A message posted at WOODWEB's Sawing and Drying Forum (7/17) -- I am purchasing a Nyle DH 200 kiln. I am interested in kin drying Douglas fir beams a ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/8/22) -- First off, who has a kiln that you can do a 10x6 in what is basically a juvenile tr ...
Re: Kiln drying oak / Croatia A message posted at WOODWEB's Sawing and Drying Forum (1/3) -- You might want to read DRYING HARDWOOD LUMBER, which is available on the Internet. Fre ...
Re: kiln drying old heart pine A message posted at WOODWEB's Sawing and Drying Forum (3/28) -- Just a few questions that will help with answering your question. Yes with it being h ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Hi Charlie - the boards are now 5 1/2 thick and 11 1/2 wide. The shrinkage calculator ...
Re: Building a wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- Wood-fired kilns should be designed so that the flue gases do not go into the kiln, b ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/18) -- Wouldn't loading half a charge in the kiln slow the drying process and cause uneven d ...
Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (10/6) -- Good Evening WoodWeb Community, I'm thankful for the ability to come here and seek ad ...
Augmenting Solar Kiln A message posted at WOODWEB's Sawing and Drying Forum (10/3) -- Hello – I read Dr. Wengert’s response on the forestry forum regarding the issue of ad ...
Re: Kiln drying oak / Croatia A message posted at WOODWEB's Sawing and Drying Forum (1/3) -- Good day and than You for reply. I'll surely look up for mentioned webinar & have ...
Solar Kiln in a Humid Climate A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- Dr. Wengert: First of all, I would like to thank you for your many contributions I hav ...
Re: Thickness standard for 5/4? A message posted at WOODWEB's Sawing and Drying Forum (4/2) -- Clarification: "For kiln dried rough lumber, the Rules require the thickness to b ...
Re: DH kiln vs Vacuum kiln A message posted at WOODWEB's Sawing and Drying Forum (7/28/22) -- I have run both conventional dh and vacuum kilns and the speed of the vacuum kiln ...
Another Powderpost beetle problem A message posted at WOODWEB's Sawing and Drying Forum (5/27) -- I was getting some wood from my stash this weekend and found exit holes and powder ri ...
Drying mixed species (ash/cherry) in a solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/25) -- I've been sawing and drying thousands of feet of ash over the last couple of years, a ...
low humidity A message posted at WOODWEB's Sawing and Drying Forum (3/23) -- I'm having issues keeping my relative humidity and wet bulb settings in my DH kiln. I ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/23) -- LOL Jennifer, I never mentioned gluing. I mentioned understanding greenwood and prope ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/16/22) -- Well, I had posted a photo, but it's never a sure thing on this site, so let's try ...
Re: solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/13) -- Thanks Gene, so how then do the drying times compare from a solar kiln to an electric ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/11/22) -- I have a Timberking mill and harvest logs off my property, cut them into lumber or ...
Re: secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/8) -- You would have to have a solar kiln that is essentially a closed room with a separate ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/7) -- Thank you for the reply, the kiln was loaded 2 days ago. I have the same amount of spa ...
Re: Building a wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (2/7) -- A wood stove outside the kiln and having air drawn over it and blown into the kiln is ...
Re: secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/1) -- I agree with Gene, Take 3 day grading and drying courses. I did, you will identify the ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Ok Now the boards are stickered in the shade next to the kiln. My understanding of th ...
Re: Finally going to build a Solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/25) -- I built the original kiln in 1978 but it is no longer around. Today is called the Vir ...
Re: Kiln Newbie A message posted at WOODWEB's Sawing and Drying Forum (1/22) -- If you have production in mind, completely off the grid is not an option yet. The bal ...
Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/19) -- This is a project I've been planning for a long time. I'm building a portable solar k ...
Re: solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/15) -- Thank for your help. I am planning to install this kiln off site, at a location with ...
Re: Solar Kiln from Storm Smashed Greenhouse A message posted at WOODWEB's Sawing and Drying Forum (11/12) -- Thank you Gene, I am in central Ill, according to everything we are in for a bad win ...
Solar Kiln from Storm Smashed Greenhouse A message posted at WOODWEB's Sawing and Drying Forum (11/11) -- My lovely bride has expressed displeasure at our back porch being filled with green ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/11/22) -- Lumberjacktim, I'm confused between post #1 and post #7. The responses you got wer ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- Additionally if you really wanted to get fancy you could duct some return air from t ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/28) -- Tim, I think some of what I said got slightly misinterpreted. I'm not denying the fac ...
Re: Newbie In Over My Head A message posted at WOODWEB's Sawing and Drying Forum (1/28) -- Most live edge slabs in my area are cut 10/4 so that after flattening you end up with ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- Until we had dehumidification power for the kilns (the early unit operated with Freon ...
Drying 8/4 white oak A message posted at WOODWEB's Sawing and Drying Forum (1/23/24) -- Hi all, I am trying to dry 8//4 white oak in a DH kiln. Slabs were air dried and s ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/21) -- Heinrich, Sawing the piece into boards, then reassembling has its own issues. When yo ...
Deadpiling wood in a kiln year round A message posted at WOODWEB's Sawing and Drying Forum (3/21) -- I usually have a stack of 1000bf or so in my shop. I want to free up some space so I' ...
Re: Thick, Large Black Walnut Slabs A message posted at WOODWEB's Sawing and Drying Forum (8/19) -- A couple of comments... First, go ahead and invest in a moisture meter. They are not ...
Re: 6/4 8/4 maple drying A message posted at WOODWEB's Sawing and Drying Forum (4/19) -- Thank you for the response Dr Gene. I would surmise then that I should keep the kiln ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/18) -- Two comments... When loading a kiln with mixed MCs, load the wetter lumber first and ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/18) -- Two comments... When loading a kiln with mixed MCs, load the wetter lumber first and ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/17) -- The front probe is above the fan deck in front of the fan and the back probe is about ...
6/4 8/4 maple drying A message posted at WOODWEB's Sawing and Drying Forum (4/16) -- I tend to dry some thicker soft maple in the 6/4 and 8/4 range. I have had problems w ...
Re: Solar kilns and cold cloudy days A message posted at WOODWEB's Sawing and Drying Forum (12/15) -- As a rule of thumb, 50 F or warmer dries wood at a somewhat reasonable rate, if ther ...
First solar kiln load results A message posted at WOODWEB's Sawing and Drying Forum (7/15) -- I just recently finished drying the first load of 4/4 ash in the solar kiln I built a ...
40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- Does anybody have experience or can comment or has heard of somebody kiln drying larg ...
Huge quartersawn oak problem A message posted at WOODWEB's Sawing and Drying Forum (3/14) -- We are a high-end european furniture producer which is working only in complete solid ...
Re: solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/13) -- Solar kilns seldom have any controls. The fans and vents are operated manually--fans ...
solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/12) -- should I attempt to apply the same trying schedules on a solar kiln as for an electri ...
Re: Wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (6/10) -- The flue gasses go out an external chimney, what I have is a residential type wood bu ...
Wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (6/9) -- I have a 3000 bf kiln with Nyle dh system stuck a large wood burning furnace on back, ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/9/22) -- Nice cant. I owned a portable band mill and had a small kiln for approximately 20 y ...
Re: secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/9) -- Radiant floors are a bad idea in kilns. To work the temperature of the floor always ha ...
Recommendations for solar kiln controls A message posted at WOODWEB's Sawing and Drying Forum (5/8) -- I'm getting close to completing a solar kiln project based on the VT plans for a 1,000 ...
Re: wood kiln A message posted at WOODWEB's Sawing and Drying Forum (11/4/23) -- Hi Ron, I have not heard of floor heating, but in theory it could work and would b ...
Re: Drying 16/4 Walnut A message posted at WOODWEB's Sawing and Drying Forum (4/2) -- We sell a lot of wide, thick live edge slabs, particularly walnut, but some pecan and ...
Re: Building a wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (2/2) -- Gene, I want to build a solar kiln like you have often described. Would a wood stove o ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/31) -- Mark, the main thing is to be careful with the safety side of this...MOST DH units h ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Hello Dan, What is the finished thickness, width and length of the stair treads? Wher ...
Advance Kiln Drying Workshop A message posted at WOODWEB's Sawing and Drying Forum (1/27) -- Penn State Extension in partnership with the Keystone Kiln Drying Association will be ...
Re: Powder post or Ambrosia? A message posted at WOODWEB's Sawing and Drying Forum (3/25) -- The ambrosia likes or requires 30% MC and higher; oftentimes the literature says over ...
Re: Kiln Newbie A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- Where are you located? It is hard to mix solar and electric. The reason is that a sol ...
Re: RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/16/23) -- Steel will be galvanized, so no problems there. Some wood movement is to be expect ...
Kiln dried lumber moisture regain to ambient EMC A message posted at WOODWEB's Sawing and Drying Forum (6/12) -- I've been operating a Virginia Tech design solar kiln for a year now, and am curious ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (10/7) -- There is no rule or guideline on how long to air dry, but 6months in a kiln uses a lo ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (3/5/23) -- The kiln process involves the drying of wood in a chamber where air circulation, re ...
Re: Equipment selection on dry kiln for wood A message posted at WOODWEB's Sawing and Drying Forum (11/3/22) -- Update on my Dry Kiln: It has been a slow process constructing this but I am happy ...
Kiln drying oak / Croatia A message posted at WOODWEB's Sawing and Drying Forum (1/2) -- Gentlemen best of luck in 2021 from Croatia! My name is Mario and I work for hardwood ...
Wood Kiln Moisture Barrier A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- When installing a moisture barrier in the walls, floor and roof a dehumidification kil ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/31) -- When the hot air from a heater goes into the kiln without the use of a plenum that i ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- Just use any heater that will deliver the btu/wattage input you need and locate the ...
Re: Bugs A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- From most of the reading I've done on solar kilns the temp will get to the heat you ...
Re: Bugs A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- I build a plenum in the kiln (it's a small kiln, only about a 150 qft) with a pretty ...
Bugs A message posted at WOODWEB's Sawing and Drying Forum (10/29) -- So I thought that the wildlife in wood would die off at 130 degrees in the kiln. Tod ...
air circulation in kiln A message posted at WOODWEB's Sawing and Drying Forum (10/29) -- I live in NW Ohio. I built a small solar kiln 5 X 10 with 60 SQ. Ft. of greenhouse g ...
Re: New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (2/28/23) -- If I air dry until it is down to 12-15%, that will take a couple of years. I thoug ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (4/25/22) -- That would be "AC Infinity" controller 67 or 69. Newest will have wifi. ...
Re: Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/22) -- In the upper right corner of the screen, type in "solar kiln" as a search i ...
kiln roof A message posted at WOODWEB's Sawing and Drying Forum (8/20) -- Is the double wall really needed on the roof? I am replacing the roof of my Solar Kil ...
New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (2/20/23) -- Hello, I bought my saw approx. a year ago cut up some slabs and built a solar kiln ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (2/20) -- Kiln drying is also hard on the substructure of the wood damaging it and does not las ...
Re: homemade kiln A message posted at WOODWEB's Sawing and Drying Forum (11/19) -- Yes, yes and no. A heat pump kiln is also called a dehumidifier. The heat is pumped ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/18) -- Brian I very much appreciate your input. But unfurtunatly it is the mass of these tre ...
Re: DH kiln vs Vacuum kiln A message posted at WOODWEB's Sawing and Drying Forum (3/18) -- I have clients with a vacuum kiln. Financially, it is profitable if you keep it full ...
DH kiln vs Vacuum kiln A message posted at WOODWEB's Sawing and Drying Forum (3/17) -- We are in the market for a kiln, we've been milling for over 10 years and the person ...
Re: DH kiln vs Vacuum kiln A message posted at WOODWEB's Sawing and Drying Forum (3/17) -- Night and day difference in time and degrade. I have no personal experience with a va ...
Re: First solar kiln load results A message posted at WOODWEB's Sawing and Drying Forum (7/16) -- 1. I assume that you appreciate that the drying rate is based on the RH, velocity and ...
Re: First solar kiln load results A message posted at WOODWEB's Sawing and Drying Forum (7/16) -- Thanks Gene .... particularly the maximum loss/percentage clarification ... sometimes ...
Re: First solar kiln first load questions A message posted at WOODWEB's Sawing and Drying Forum (7/15) -- After running the first load, I have some questions I hope Gene can weigh in on... 1 ...
Re: Cool down times???? A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- The problem that we are seeing is that when cutting the prongs we see no stress and t ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/14/22) -- I don't know if it can get to 150F but it gets up to 140F w/o a problem, as long a ...
Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (1/14) -- Maybe you have heard of the Marc Adams School of Woodworking in Franklin, IN. They ha ...
homade dry kiln heat source A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- So I have built a temporary 12x5 kiln in half of my garage. I have a wood furnace th ...
Re: solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/13) -- Problem with pure solar kiln is that drying times is not predictable. I am busy build ...
Cool down times???? A message posted at WOODWEB's Sawing and Drying Forum (4/12) -- I am a kiln operator for a cabinet manufacturer in PA. Currently it seems there has b ...
Re: pine/spruce stakes A message posted at WOODWEB's Sawing and Drying Forum (12/11) -- Can you run a test the left with someone else's equipment first? My impression of yo ...
Re: River Birch mill thickness prior to kiln dry A message posted at WOODWEB's Sawing and Drying Forum (2/11) -- Shrinkage in drying to 6% MC is about 7.4% on the average. A few pieces will shrink a ...
Re: Wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (6/10) -- The outdoor wood burner boiler is the ideal system aka "southern boiler" an ...
Re: Live edge slabs, is the hype real? A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- Doug, A great question. Are those slabs on your trailer kiln dried? If not how, and ho ...
kiln doors A message posted at WOODWEB's Sawing and Drying Forum (4/9) -- I am looking to build new doors for my kiln. I currently have 2x4 doors insulated with ...
supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/9/22) -- I built a solar kiln back in 2009 following the Virginia Tech design and this has w ...
drying doug fur lumber A message posted at WOODWEB's Sawing and Drying Forum (7/8/22) -- I have a nyle dehum. kiln, last time we dryed Douglas fur 2x6 we followed nyles woo ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/8/22) -- I sometimes wonder if people responding to posts are basing their opinions on “what ...
secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/8) -- I intend on building a solar kiln to hold 10,000 bf, at the same time I will be buildi ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/7/22) -- Just my personal opinion but eliminating the pith is going to be your most stable s ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (11/6) -- You may have a tough time getting the BTU conversion you need with radiant unless you ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/6) -- Your square corners (walls meeting ceiling) are part of the problem. The air hits flat ...
Re: safe rate for moisture removal A message posted at WOODWEB's Sawing and Drying Forum (7/4) -- It is virtually impossible to damage air dried lumber unless you add moisture back whe ...
Cutting Slabs A message posted at WOODWEB's Sawing and Drying Forum (11/3) -- I haave a Lucas Mill & a Tree Service, A customer has hired me to remove his tree ...
drying wood A message posted at WOODWEB's Sawing and Drying Forum (7/3) -- I've dried a couple of loads in our kiln, the first being western red alder, then figu ...
Re: worms in pine A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- Bill it's obvious he's never seen ANY termites......fly...yes a part of them do fly BU ...
Re: Building a wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (2/2) -- You can use a Garn hot water boiler to both kiln dry and sterilize lumber. The amount ...
Re: old house boiler into a kild A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- I think Gene thought you were going to make a house into a kiln. I read it that you wa ...
Re: Using tobacco kiln to dry lumber? A message posted at WOODWEB's Sawing and Drying Forum (12/29) -- What species and thickness? What moisture content now? What temperature and RH is in ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Charlie - you asked me if I'd built a kiln before. No, this is the first. I modified ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Do you have any experience drying lumber. A dry kiln is a controlled environment when ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- There were a few cracks after milling, but they were the air dried log ends. I coated ...
Re: Free Webinar, 8/26/2020 Drying oak And Maple A message posted at WOODWEB's Sawing and Drying Forum (8/26) -- Gene, and others, I will not be able to attend the Webinar due to work, but have the ...
Re: Dehumidifier or AC? A message posted at WOODWEB's Sawing and Drying Forum (5/26) -- Definitely a dehumidifier, like John said, it adds heat, and an AC doesn't have a pur ...
Re: Solar Kiln - Ash drying questions A message posted at WOODWEB's Sawing and Drying Forum (2/25) -- A solar kiln does not get hot enough for sterilization. Due to its poor energy effici ...
Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/23) -- Hi Again - In the end I've constructed a solar kiln to reduce the MC in my old growth ...
Re: Kiln Advice A message posted at WOODWEB's Sawing and Drying Forum (4/23) -- The wood lined kiln is not functional in the US for hardwoods. You need a dehumidifie ...
Re: Kiln Newbie A message posted at WOODWEB's Sawing and Drying Forum (1/23) -- FWIW: Such a deal. Go for it. What's to lose? But get an iron clad agreement of what ...
Re: Mini Kiln questions A message posted at WOODWEB's Sawing and Drying Forum (7/21) -- You'll need a super slow cycle at the beginning. A solar kiln in Texas in the summer ...
Kiln Advice A message posted at WOODWEB's Sawing and Drying Forum (4/21) -- The company I work for has plans to open a sawmill with a kiln. I have heard of a woo ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/21) -- Thanks Jessica, I didn't want to get into all the heavy details as it does get overwh ...
Re: RE: Making a Kiln A message posted at WOODWEB's Sawing and Drying Forum (11/16) -- Sure you can! Yes you need a fan or two. I use a modified electric baseboard heater ...
Re: Final stages in dh kiln A message posted at WOODWEB's Sawing and Drying Forum (1/16) -- Let me add to my perceived understanding on how this works and would look to be strai ...
Mini Kiln update A message posted at WOODWEB's Sawing and Drying Forum (9/15/21) -- Thanks for the advice. Update: I put about 80 board feet of a mix of 4/4, 6/4, 8/4 ...
Re: Cool down times???? A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- I wonder why the Dry Kiln Operators' Manual, Drying Eastern Harwood Lumber and Drying ...
Re: Kiln Advice A message posted at WOODWEB's Sawing and Drying Forum (2/15) -- was your dehumidifier kiln indoors i am trying to decide on something to speed up my ...
RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/14/23) -- I’m in the process of finalizing an outdoor project that requires some White Oak T ...
Re: Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/14) -- How much lumber is in the kiln? If it is 50 MBF and you run about 20 loads a year, th ...
RE: Making a Kiln A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- Can I make a kiln out of 4x8 4-inch thick insulation panels on a concrete floor? Wha ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (1/13) -- Den is not correct. He should have said "a properly designed and properly run va ...
Drying Cypress A message posted at WOODWEB's Sawing and Drying Forum (3/12) -- Gene, A major flood took down a large number of cypress tress near Wimberly Tx a few ...
River Birch mill thickness prior to kiln dry A message posted at WOODWEB's Sawing and Drying Forum (2/9) -- Want to make a dining room table. No experience milling/kiln dry. Have River Birch in ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (10/5) -- Kiln drying all the way. The benefits of air drying over kiln drying are insignifican ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/31) -- UPDATE.... I found the pics....Did I mention MELT DOWN!!!! Top pic mini kiln.... 2nd ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (5/31/25) -- I built a solar kiln last summer—super rewarding project! I used rigid insulation ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- Not knowing size of kiln, Check out the units in the counter top baking ovens. ...
Re: Bugs A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- Although the air was 140 F for a brief time, it is likely that the wood was below 13 ...
Re: Drying Black Spruce dead straight A message posted at WOODWEB's Sawing and Drying Forum (5/30) -- Hi once again. Just finally started up the Nyle L200 kiln in the chamber. Air dried w ...
Re: Very small batch to dry (two boards) A message posted at WOODWEB's Sawing and Drying Forum (3/30) -- In all seriousness, how well would an old car, station wagon or van do as a makeshift ...
wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/29) -- Hi I've built a wood kiln and read other threads on this topic. Specifically I need ...
Solar drying fire wood to kill all insects A message posted at WOODWEB's Sawing and Drying Forum (9/29/23) -- Hi, I have been trying to find out if my solar dried fire wood is safe to bring fr ...
Re: Old growth Cherry, possible value? A message posted at WOODWEB's Sawing and Drying Forum (8/29) -- Chances are that the cherry is "mill run" meaning everything that was sawn ...
Re: Dry 3 Inch Red Oak A message posted at WOODWEB's Sawing and Drying Forum (3/29) -- I'd be looking for a good vacuum kiln guy with those. Go directly from the log to the ...
Re: Newbie In Over My Head A message posted at WOODWEB's Sawing and Drying Forum (1/29) -- Normal air drying can usually air dry 8/4 oak if a few precautions are taken. But, 12 ...
Re: Steaming for the purpose of conditioning. A message posted at WOODWEB's Sawing and Drying Forum (11/28) -- Injection of steam into the air at room temperature has an EMC of around 22% MC, so ...
Re: old house boiler into a kild A message posted at WOODWEB's Sawing and Drying Forum (3/28) -- If you turn your house into a kiln, you would need at least four times bigger boiler. ...
kiln drying old heart pine A message posted at WOODWEB's Sawing and Drying Forum (3/28) -- Greetings, I have pine wood about 150 years old and a new kiln dryer we built. I am m ...
Re: Dehumidifier or AC? A message posted at WOODWEB's Sawing and Drying Forum (5/27) -- I used a cheap DH in my 275 bf capacity kiln for 20 years w/o problems, but I only pu ...
Re: New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (2/27/23) -- I bought a Delmhorst moisture meter J-2000 used for $190.00 on Facebook. It works ...
Using tobacco kiln to dry lumber? A message posted at WOODWEB's Sawing and Drying Forum (12/26) -- I have a bunch of white oak boards that i cut about a month ago. I would like to use ...
Live Oak Sandbox - Rot Resistance and Drying A message posted at WOODWEB's Sawing and Drying Forum (5/26/22) -- I am building a live oak sandbox for my kids, due to its rot resistance, but have ...
Drying wood in a tropical climate A message posted at WOODWEB's Sawing and Drying Forum (5/26/22) -- I am in Thailand, where the RH on a normal day ranges from 45% to 80%, which IMHO ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (4/26/22) -- George could you send some pictures of your system? I am in the process of buildin ...
southeastern kiln club A message posted at WOODWEB's Sawing and Drying Forum (2/26) -- I'd like to get to talk to a couple of kiln owners here that belong to the club to ge ...
L200M problems A message posted at WOODWEB's Sawing and Drying Forum (12/25) -- I have a new L200M that I am running its second load thru. I believe it has not been ...
Re: Finally going to build a Solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/24) -- The big concern with such products is how they will perform when the temperature gets ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (1/24) -- Here is a 1/2 scale model of the kiln that my grandson (8 years) and I built this wee ...
Re: Need to kill some bugs A message posted at WOODWEB's Sawing and Drying Forum (12/23) -- Thanks for the info. The plan for the wood is to put it in a pole barn, not near any ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/23) -- Dr. Gene - I plan to take this class and I like using our camper pulled behind my tru ...
Building a wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (1/23) -- I am in the planning stages of building a kiln. I would like to use this to dry as we ...
Re: Can I use radiator fans? A message posted at WOODWEB's Sawing and Drying Forum (11/22/23) -- Yes, you can use radiator fans in your solar-powered kiln. Radiator fans are desi ...
Re: Temps and humidity A message posted at WOODWEB's Sawing and Drying Forum (7/22/23) -- My apologies, I wrote my question in hast. I am air drying first for about a month ...
Oak drying A message posted at WOODWEB's Sawing and Drying Forum (4/22) -- I had a customer ask if we could dry some 2" thick oak in our solar kiln. He sai ...
Re: Deadpiling wood in a kiln year round A message posted at WOODWEB's Sawing and Drying Forum (3/22) -- If you want 7.0% MC, then you will be fine if you keep the kiln at about 35% RH. Temp ...
Temps and humidity A message posted at WOODWEB's Sawing and Drying Forum (7/21/23) -- I have my solar kiln (VT style) up and running here in Texas, and it is getting ho ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/21) -- I very much appreciate all your input. Ec Aumiller I' am all with you on getting it d ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/21) -- I am starting to think that it might be best to find a client with a covered pergola ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/21) -- Thanks Mark, that makes sense and I'll look into that the next time around. My intent ...
Heat treating lumber for export/import A message posted at WOODWEB's Sawing and Drying Forum (3/21/25) -- In the heat treating for export listings online all I see are companies that provi ...
Re: Dehumidification H20 output monitoring A message posted at WOODWEB's Sawing and Drying Forum (2/21/22) -- Answer to question about my dehumidifier and comments re: same. I was fortunate to ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/21) -- Oak is a very hard specie to dry because it is very prone to checking and splitting. ...
hygrometers A message posted at WOODWEB's Sawing and Drying Forum (1/21) -- Hello all, I'm trying to find a source to purches hygrometers to hang in dry kilns an ...
Drying SYP A message posted at WOODWEB's Sawing and Drying Forum (1/21) -- At what temp does green SYP start to turn blue?? Assuming that is is fresh from the s ...
Re: 6/4 8/4 maple drying A message posted at WOODWEB's Sawing and Drying Forum (4/20) -- Thank you again for your help. My MC of my hard maple is at 24% right now and my wet ...
Re: New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (2/20/23) -- I suppose you have this guide to operation of the Virginia Tech kiln? Lots of vide ...
Re: Large Scale Drying A message posted at WOODWEB's Sawing and Drying Forum (12/19) -- Yard trees are known to have excessive stress, called growth stress, that will resul ...
homemade kiln A message posted at WOODWEB's Sawing and Drying Forum (11/19) -- Im new to sawmilling, and have been doing alot of reading on drying lumber, and kiln ...
Re: homemade kiln A message posted at WOODWEB's Sawing and Drying Forum (11/19) -- That won't work very well or last very long. It will use a lot more energy than if y ...
Dying hemlock slabs A message posted at WOODWEB's Sawing and Drying Forum (9/19) -- Have 2 hemlock slabs 8/4 x 21"x 8'6" that have been air dried for one year. ...
Drying SYP Timbers for Transport A message posted at WOODWEB's Sawing and Drying Forum (2/19/24) -- A customer in mid-Atlantic area (we are in south Georgia) is looking for 8"x8 ...
Old nyle l200 won't heat up A message posted at WOODWEB's Sawing and Drying Forum (2/19/23) -- I purchased an older L200 nyle kiln last year and it was a game changer for our fa ...
Re: Large Scale Drying A message posted at WOODWEB's Sawing and Drying Forum (12/18) -- Your main source of material is going to be yard trees? Good luck with that, you're ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/18) -- Thank you for your responses Gene. The red oak is at 100/96, not 110/106 which accord ...
Drying 8/4 Cypress A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- Any idea on how long to air dry 8/4 Cypress before being able to safely dry it in the ...
Re: when can we use white oak? A message posted at WOODWEB's Sawing and Drying Forum (12/17) -- KP If you have a little bit of time,especially if you really like your slabs, a opti ...
Re: DH kiln drying douglas fir beams and posts A message posted at WOODWEB's Sawing and Drying Forum (7/17) -- To add: If the beams with your dad had been fully AD'd the twist shouldn't have happe ...
Re: Equipment selection on dry kiln for wood A message posted at WOODWEB's Sawing and Drying Forum (5/17/22) -- I don't see any plans for sterilizing the wood. You'll have to bring the kiln up t ...
Re: Avoiding Stain in Hickory A message posted at WOODWEB's Sawing and Drying Forum (5/17) -- Forget about dipping as that is a fungicide and blue stain fungus is seldom an issue ...
kiln help A message posted at WOODWEB's Sawing and Drying Forum (1/17) -- Just curious if anyone knows of any people who do short courses for kiln operators at ...
Re: when can we use white oak? A message posted at WOODWEB's Sawing and Drying Forum (12/16) -- I will throw my two cents in on this issue. I am in western Oregon and mill and dry ...
8/4 redoak A message posted at WOODWEB's Sawing and Drying Forum (11/16) -- I will be drying some 8/4 redoak soon in a dry kiln and I'm wondering what's the bes ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/16/22) -- Thanks Rich and John for you input on this. John you mentioned pictures of your ki ...
Re: kiln drying sinker Caribbean heart pine A message posted at WOODWEB's Sawing and Drying Forum (1/16) -- At this low MC (under 25%), your only concern is drying the wood too dry...that is, o ...
Re: Varying MC kiln dried red oak A message posted at WOODWEB's Sawing and Drying Forum (12/15) -- It is not unusual to see a wide range of green MCs in oak. For that reason, we do ne ...
Re: First solar kiln - structure pictures A message posted at WOODWEB's Sawing and Drying Forum (7/15) -- Some pics of the kiln - the plan is to stain it black when the board and batten sidin ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- Heinrich, I would NOT put your carved bench into a kiln. Kilns are designed and meant ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- Thank you Mark, I was afraid of the no kiln response, because actually my biggest iss ...
Re: Cool down times???? A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- Your question is a good one. The prong tests require NO MOISTURE GRADIENT in the piec ...
Final stages in dh kiln A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- First off, I've gotten this far reading as much as I could find. Need a little help g ...
Re: Dehumidification kiln choice A message posted at WOODWEB's Sawing and Drying Forum (8/14) -- I agree with Don. I started using Nyle kilns in 1989. They answered every question I ...
Re: Wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (6/14) -- I have a large Taylor outdoor wood burning boiler furnace that I circulate water thro ...
Re: solar vs. electric kiln drying schedules A message posted at WOODWEB's Sawing and Drying Forum (5/14) -- You might check out Gene's article on solar kilns in the current issue of Sawmill &am ...
kiln drying sinker Caribbean heart pine A message posted at WOODWEB's Sawing and Drying Forum (1/14) -- I am three years into a project in Nicaragua, recovering 100 year old, old growth log ...
Re: Bugs A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- Hmm, thanks Gene, when you put it like that it makes sense. I guess for the drying p ...
Dehumidification kiln choice A message posted at WOODWEB's Sawing and Drying Forum (8/13) -- Good morning to all. I'm finishing up a kiln chamber and was looking for advice on pu ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/13) -- Thank you for responding, Iam getting plenty on movement through the stack with the n ...
Re: Drying Cypress A message posted at WOODWEB's Sawing and Drying Forum (3/13/24) -- It would help to know the species of cypress and what kind of kiln you have, but t ...
Re: homade dry kiln heat source A message posted at WOODWEB's Sawing and Drying Forum (12/12) -- What kind of kiln schedule are you using? ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (9/12/24) -- Has anyone used PVC(vinyl) roofing membrane on the floor and walls of a solar kiln ...
Re: Drying wood prior to using kilns? A message posted at WOODWEB's Sawing and Drying Forum (8/11) -- Was pine less susceptible to fungal staining back then? My understanding is that whit ...
Can I dry wood too much A message posted at WOODWEB's Sawing and Drying Forum (8/11) -- I recently finished building a solar kiln and have my first load in. How important is ...
Re: RE: Table Making-- Best Method A message posted at WOODWEB's Sawing and Drying Forum (5/11) -- Let’s say you have a 12” wide Icee with 1” of cup. If you cut this in half to get two ...
Re: kiln doors A message posted at WOODWEB's Sawing and Drying Forum (4/11) -- You can also make the doors very much like a barn door, recessed in the frame, heavy ...
Re: drying red elm A message posted at WOODWEB's Sawing and Drying Forum (6/10) -- My concern is that the solar kiln might dry the elm too fast. Does anyone have experi ...
Re: Wood fired kiln A message posted at WOODWEB's Sawing and Drying Forum (6/10) -- Do you mean that the kiln is part of the chimney? In a house, there is a plenum, so t ...
Re: kiln doors A message posted at WOODWEB's Sawing and Drying Forum (4/10) -- If you make wood kiln doors, don't have them recessed or between the jambs. Have them ...
Re: Varying MC kiln dried red oak A message posted at WOODWEB's Sawing and Drying Forum (12/9) -- Thank you for the input. Pin meter corroborates the pinless meters story. I think I n ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (9/9) -- Hi there my first charge is about to come out it was interesting how it dried it was s ...
Re: Recommendations for solar kiln controls A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- Thanks, Gene - the keep-it-simple suggestion makes sense, and is certainly the easy wa ...
Re: microwaving prong tests??? A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- The key for stress relief is rapid addition of moisture to the wood at high temperatur ...
Re: drying bamboo A message posted at WOODWEB's Sawing and Drying Forum (3/9) -- Thanks Don, The L200s got some miles on them but they keep going with a little coaxing ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (1/9) -- For those people without the article, the best approach for color is that if you are g ...
Re: drying doug fur lumber A message posted at WOODWEB's Sawing and Drying Forum (11/8/22) -- found out from stan at nyle that you need to bring up humidity while setting sap a ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (9/8/22) -- Hey Tim, I have been real busy with a big job. Also redesigned the kiln setup. Do y ...
Re: Kiln Advice A message posted at WOODWEB's Sawing and Drying Forum (8/8) -- i built a small (13x13)kiln,for specialty wood,spalted maple,hickory,burlwoood & l ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (4/8/22) -- If you shop for a dehumidifier kiln, make sure it has the ability to bring the whol ...
Re: Staining on white oak lumber A message posted at WOODWEB's Sawing and Drying Forum (2/8/23) -- That bits that they won't take it back for ruining suck good looking wood. It doesn ...
Re: drying to single digits p2 A message posted at WOODWEB's Sawing and Drying Forum (1/8) -- It's impossible to say how long it will take to dry from one MC to another. It depends ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/7) -- Stuart, I'm a little concerned on your drying schedule. I do a completely different sc ...
Re: controlling the humidity in kilns A message posted at WOODWEB's Sawing and Drying Forum (2/7) -- In this colder weather, it is not uncommon to find that the floor or other area withou ...
Re: How straight should 10/4 oak be after drying A message posted at WOODWEB's Sawing and Drying Forum (1/7) -- This is an interesting question. I wonder, how much did you pay for this stock? > 1 ...
Re: Solar kilns and cold cloudy days A message posted at WOODWEB's Sawing and Drying Forum (12/6) -- Sounds to me that under your winter conditions you are in zero gain situation using a ...
Re: Solar Kiln Workshop Online A message posted at WOODWEB's Sawing and Drying Forum (8/6) -- There are two days left to register for the VT Solar Lumber Drying Workshop. The works ...
Re: Drying wood prior to using kilns? A message posted at WOODWEB's Sawing and Drying Forum (8/6) -- You can learn about this at Colonial Williamsburg, where wood was stacked and air drie ...
Drying wood prior to using kilns? A message posted at WOODWEB's Sawing and Drying Forum (8/6) -- I am new to the sawmill world, but a long time carpenter. I am wondering how wood was ...
Dehumidification air speed A message posted at sawdry (12/31) -- I have just finished building a simple DH kiln The size is mm High By mm wide long I have loaded a stack of mm ...
Re: How to kill bugs in an infested log....??? A message posted at WOODWEB's Sawing and Drying Forum (6/6) -- OK so seems like heating is the way to go. I'm thinking about using some insulation pa ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/6) -- There is no difference between the two if they are at the same moisture content AND if ...
killing bugs in beams with heat. A message posted at WOODWEB's Sawing and Drying Forum (3/6) -- I have beams SY pine 8x6,8x8, 8x10 and some cants that are larger that I plan to re-sa ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/6) -- I am not sure what the inside will be like. The walls and floor of the VT kiln are not ...
Re: wood kiln A message posted at WOODWEB's Sawing and Drying Forum (11/5/23) -- Depending the on the wood, dehumidification without sufficient heat is not a good ...
Vacuum Drying A message posted at WOODWEB's Sawing and Drying Forum (9/5) -- We've been looking at vacuum drying options for specialty hardwood slabs and timbers. ...
Re: Sterilizing reclaimed wood for kitchen. A message posted at WOODWEB's Sawing and Drying Forum (7/5) -- It is indeed best to sanitize "according to the book, and document in writing wha ...
Re: 8/4 red oak A message posted at WOODWEB's Sawing and Drying Forum (1/5) -- Yes, this is best for quality, but not for your pocket book. One hundred days in the k ...
Varying MC kiln dried red oak A message posted at WOODWEB's Sawing and Drying Forum (12/4) -- I just removed my first load of 4/4 red oak from our Nyle L53 DH kiln. All my sample ...
Re: splits in large slabs A message posted at WOODWEB's Sawing and Drying Forum (6/4) -- If you dry enough slabs to justify the investment, a vacuum kiln makes a lot of sense. ...
Drying 16/4 Walnut A message posted at WOODWEB's Sawing and Drying Forum (3/4) -- Gentlemen , I am seeking council. I have a 16/4” Black walnut slab (44”x9’) that has b ...
Re: Drying 16/4 Walnut A message posted at WOODWEB's Sawing and Drying Forum (3/4) -- I don't know for sure, all the seller could tell me was it was Black Walnut. The slabs ...
wood kiln A message posted at WOODWEB's Sawing and Drying Forum (10/3/23) -- Has anybody ever used hot water floor heat in a wood kiln? ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (8/3/24) -- I’ll be honest George that looks super freakin cool. Is your setup mounted to a ree ...
Re: severe checking in air-dried white oak A message posted at WOODWEB's Sawing and Drying Forum (4/3) -- If it then goes in a kiln, why not put it in the kiln sooner. Air drying isn't simple. ...
Black Walnut Tree A message posted at WOODWEB's Sawing and Drying Forum (4/3) -- I have a Black Walnut Tree that is over 11' in circumference at 5' high on the trunk. ...
Finishing air dried lumber A message posted at WOODWEB's Sawing and Drying Forum (1/3) -- I have some 2 year air dried 5/4 walnut running 12-14% MC. I would like to dry the lum ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (11/2) -- Thanks everyone for the feedback. I guess the jist of this is that there is no quick ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (11/2) -- I had an idea.... electric floor radiant heating system. This way no flame combustion ...
solar kiln A message posted at WOODWEB's Sawing and Drying Forum (11/2) -- I'm currently finishing up the VT solar kiln project.. still have about two weeks wor ...
Re: Solvent/Chemical Drying A message posted at WOODWEB's Sawing and Drying Forum (10/2) -- There aren't any commercial kilns using this method then? I looked around on YouTube ...
Re: Thick, Large Black Walnut Slabs A message posted at WOODWEB's Sawing and Drying Forum (9/2) -- It is amazing what research does. I want to thank all of you for your concern over my ...
Re: Wet Bulb Location A message posted at WOODWEB's Sawing and Drying Forum (4/2) -- Except right close to the outflow from the DH, the WB is the same throughout the kiln. ...
solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/2) -- Gene I posted a note on FF about our solar kiln. Can you put black roofing on the outs ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/2) -- Some how, we need to get as much solar energy into the kiln. The black roofing on the ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/2) -- can i use it as a metal box . doing nothing to the outside except painting. setting up ...
solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/2) -- hi can you use a cargo container for a solar kiln ? thanks al ...
Solar Kiln Workshop Online A message posted at WOODWEB's Sawing and Drying Forum (7/1) -- After much deliberation and exploration, we have set the date for our online solar kil ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- I believe they want a dry peg so when driven in, the beam holes will shrink and lock i ...
kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- Is there an appreciable difference in strength between kiln dried and air dried wood? ...
Re: Thickness standard for 5/4? A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- Rod, I guess it depends on who your selling lumber to and how? If your selling to guys ...
Re: Thickness standard for 5/4? A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- For hardwood lumber, the requirement is that for 5/4 lumber the thickness IN THE AREA ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (1/28) -- Tommy, The question is about color retention. There are three types of drying discolo ...
Re: 1/2 Day Solar Kiln Course A message posted at WOODWEB's Sawing and Drying Forum (9/27/26) -- Wish I was local, that solar kiln course sounds like a goldmine ...
RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- If you air dry is there better color retention in the wood than if you kiln dry? ...
Re: Kiln Operation Help A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Hi Dan, I just looked back at an older post you put up and I see the finished size fo ...
VT Solar Kiln Course A message posted at WOODWEB's Sawing and Drying Forum (2/27) -- The Short Course, Drying Lumber with a Solar Kiln, will be held on Friday, May 30th, ...
Kiln Drying Workshop - Syracuse, Jan 5-8, 2015 A message posted at WOODWEB's Sawing and Drying Forum (11/25) -- We are holding our Annual Kiln Drying Workshop at SUNY ESF January 5-8, 2015 in Syra ...
Re: Solar Kiln - Ash drying questions A message posted at WOODWEB's Sawing and Drying Forum (2/25) -- Indeed, 300 bf is best for ash to achieve the whitest color when starting with green ...
Re: Solar Kiln - Ash drying questions A message posted at WOODWEB's Sawing and Drying Forum (2/25) -- Gene, How do you get it hot enough for sterilization? This part of solar kilns has al ...
NYle Kiln L200 A message posted at WOODWEB's Sawing and Drying Forum (9/24) -- Hi I am new to wood drying and wanted to know if anyone has run into this problem I r ...
Solar Kiln Interior Paint A message posted at WOODWEB's Sawing and Drying Forum (9/24) -- My solar kiln is coming along well, but I've had trouble finding the right product fo ...
Re: NYle Kiln L200 A message posted at WOODWEB's Sawing and Drying Forum (9/24) -- I am interested in getting a Nyle kiln, how old was the vents since you got them? If ...
Re: Mini Kiln questions A message posted at WOODWEB's Sawing and Drying Forum (7/24) -- Do not worry about the roof angle. Thirty degrees or whatever you have is fine. Consu ...
Maintaining MC After Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (2/24) -- If after air drying and solar kiln drying any hardwoods to the desired MC, can the wo ...
Re: Lumber Drying Workshop - March 11 A message posted at WOODWEB's Sawing and Drying Forum (2/23) -- If you go look at the forum listing on 1-27 called Advance Kiln Drying workshop you w ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/22) -- Hi there, I am concerned with my drying schedule. At the moment The Kiln is running a ...
Re: Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/22) -- Ok, I decided to place the baffle about 3" from the back wall. I figure I can al ...
Re: Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/22) -- Thank you, Dr. Wengert. 1. Right now I have some air dried lumber, but I'd like to do ...
Re: Kiln Newbie A message posted at WOODWEB's Sawing and Drying Forum (1/19) -- I think I got my words run together in my post.....I meant (seperate) solar kiln for ...
Re: air drying ash A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- Here's a guide that's posted on here of most areas.....IN Ohio to 10% ADing....IT AIN ...
Re: Kiln Newbie A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- Sounds like an interesting project. Gene would be a GREAT source of info on this larg ...
Re: Solar Kiln Question A message posted at WOODWEB's Sawing and Drying Forum (7/16) -- Building on what Gene said about vandals or hail, there's also a good chance of putti ...
Re: RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/16/23) -- Kiln drying will only last as long as the first rain. Kiln drying does not stop wo ...
Re: First solar kiln - kiln load pictures A message posted at WOODWEB's Sawing and Drying Forum (7/15) -- I had a large piece of commercial rubber roofing laying around, and use it as a tarp ...
Re: RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/15/23) -- Wy use kiln dried white oak outside? I'd put it up green. Barn builders did it for ...
Re: Drying Black Spruce dead straight A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- Update on this. The issue with the kiln was a refrigerant problem, now rectified! Kil ...
Re: Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- I was using a guy in Oregon that repaired these for Coe. I've had great service up ti ...
Re: kiln drying sinker Caribbean heart pine A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- Gene, I just went up to our mill and air drying area, and I am very surprised at the ...
Advanced Lumber Drying, Nov. 12-13, KY A message posted at WOODWEB's Sawing and Drying Forum (6/14) -- Mark your calendar. More info to follow ADVANCED DRYING SEMINAR Achieving The Objecti ...
Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/14) -- I have a Moore kiln control with gas filled capillaries. I need to have the capillari ...
Re: kiln drying sinker Caribbean heart pine A message posted at WOODWEB's Sawing and Drying Forum (1/14) -- Can you control temperature accurately? Humidity? Air velocity? What thickness? What ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- I have air dried my 8/4 slabs in my garage as long as no bugs are in the slabs. I ha ...
Re: Solar Kiln Question A message posted at WOODWEB's Sawing and Drying Forum (7/13) -- The windows to reduce heat gain are sometimes called "low e" windows, which ...
Re: Solar Kiln from Storm Smashed Greenhouse A message posted at WOODWEB's Sawing and Drying Forum (11/12) -- For effective solar drying, you need about one square foot of collector for every 10 ...
Re: Solar Kiln Question A message posted at WOODWEB's Sawing and Drying Forum (7/12) -- Built a solar kiln about 6-8 years ago.. Used double pane insulated glass from entran ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (10/11) -- I do not believe air drying will increase or decrease color retention compared to ki ...
Solar Kiln Question A message posted at WOODWEB's Sawing and Drying Forum (7/11) -- I'm thinking about building a solar kiln in the 12' by 4' or 5' size range. I have se ...
Re: RE: Table Making-- Best Method A message posted at WOODWEB's Sawing and Drying Forum (5/11) -- Lumber in general will cup some, but some more than others. Kiln dry or air dry will ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (10/8) -- I'd suggest you do a cost study on having those slabs dried in a vacuum kiln. Having ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/8) -- Tim I am following Dry Kiln Schedules for Commercial Woods Temperate and Tropical Cinn ...
Re: Timber Frame Barn A message posted at WOODWEB's Sawing and Drying Forum (6/8) -- I'm a beginning timber framer too and I've asked the same question at my training sess ...
Re: 4/4 Hickory A message posted at WOODWEB's Sawing and Drying Forum (1/8) -- Cupping is a normal tendency for lumber sawn from near the pith of the tree. Cupping i ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (12/7) -- So my first run of lumber out of the kiln went well. was able to dry my ash lumber to ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (11/7/23) -- As long as there are no bugs in the slabs, I have air dried my 8/4 slabs in my gar ...
Transporting Sawn Ash A message posted at sawdry (12/31) -- So I'm getting ready to saw and kiln several trophy ash trees in So NH and truck to MI I need to know what are ...
southeastern dry kiln club - spring 2016 A message posted at WOODWEB's Sawing and Drying Forum (3/7) -- One of the main topics for the spring meeting this year is details about drying prior ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (10/6) -- Directly to kiln can be done BUT there's higher risks IF steps aren't followed correc ...
Re: Kiln drying oak / Croatia A message posted at WOODWEB's Sawing and Drying Forum (1/3) -- Hello, I'm watching webinar & now got the understanding of "surface MC & ...
Re: Kiln drying oak / Croatia A message posted at WOODWEB's Sawing and Drying Forum (1/3) -- Do you have a pin moisture meter? This is how you measure the surface MC. We want to s ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (10/2) -- Sorry for the delayed response. By retention, I mean the normal retention of colors t ...
Re: Solar Kiln in a Humid Climate A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- If You heat foggy air by 25 F, then the humidity would be under 30%RH. So, you do not ...
Re: Kilns in West Michigan A message posted at WOODWEB's Sawing and Drying Forum (5/2) -- Derek, I run two kilns about 35 miles west of kalamazoo. you can reach me at 269-436-0 ...
Re: pine/spruce stakes A message posted at WOODWEB's Sawing and Drying Forum (12/31) -- so if a person would use the knottier pieces for a pallet operation then have clears ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/31) -- Best idea I've read about was using an element from a home oven, mounted to a thick ...
Re: Virginia Tech: Vacuum Drying Workshop A message posted at WOODWEB's Sawing and Drying Forum (10/31) -- I will be making a presentation. I will try to answer a lot of questions and deliver ...
Re: Ash defect - what causes this defect? A message posted at WOODWEB's Sawing and Drying Forum (7/31) -- I've attached another version of the photo ... my impression is that the defects run ...
Re: Drying wood in a tropical climate A message posted at WOODWEB's Sawing and Drying Forum (5/31/22) -- The DH kiln comes in all sizes and runs a different maximum temperatures. For exam ...
Re: Maintaining wet bulb temp A message posted at WOODWEB's Sawing and Drying Forum (5/31) -- another thing I found out tonight is the DH which has dual fans is putting out twice ...
Re: Moisture reabsorbtion A message posted at WOODWEB's Sawing and Drying Forum (3/31) -- Is there such a thing as EMC in an outdoor installation? I suppose there is, but it w ...
Thickness standard for 5/4? A message posted at WOODWEB's Sawing and Drying Forum (3/31) -- I'd like some insight on a situation. I've got some walnut cut to 5/4. The customer m ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- Thanks Mark B.... thinking outside the box lol. yeah, i think a fired forced air hea ...
Re: wood kiln electric heater A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- https://smile.amazon.com/gp/product/B011296704/ref ox_sc_sfl_title_3?ie UTF8&p s ...
Re: Bugs A message posted at WOODWEB's Sawing and Drying Forum (10/30) -- I was thinking that 133 degrees was the temp you needed and it did have to hold over ...
Degradation of wood when frozen A message posted at sawdry (12/31) -- Here's one for the group We fabricate what are know in the industry as Column Isolation blocks used in large fr ...
Re: "off the stump" moisture content A message posted at WOODWEB's Sawing and Drying Forum (4/30) -- While I was at Nyle, we did dozens of kilns that dried ash. Tool handles. baseball ba ...
Re: kiln drying old heart pine A message posted at WOODWEB's Sawing and Drying Forum (3/30) -- The thicker the wood, the longer you need. Start the clock when you reach 150 F, not ...
Re: Using tobacco kiln to dry lumber? A message posted at WOODWEB's Sawing and Drying Forum (12/29) -- Del, the smell of tobacco leaves is nothing like the smell of smoke. Analogy could b ...
Re: Bugs A message posted at WOODWEB's Sawing and Drying Forum (10/29) -- I thought you had to hold 135 degrees, at the core of the board, for 24 hours to ste ...
Re: air circulation in kiln A message posted at WOODWEB's Sawing and Drying Forum (10/29) -- Run the fan when it is sunny or partly sunny and the outside is above freezing. This ...
Re: How long to heat to sterilize wood A message posted at WOODWEB's Sawing and Drying Forum (8/29) -- I have lots of infected wood but will try to keep it separate. I have an old sawmill ...
Carpenter bees & dried hardwood storage A message posted at WOODWEB's Sawing and Drying Forum (8/29) -- 1st. day with my woodweb account and not sure where this question best fits so here i ...
Re: Old growth Cherry, possible value? A message posted at WOODWEB's Sawing and Drying Forum (8/29) -- In the Shenandoah Valley in Virginia (northern end) the MOST I would pay to buy the e ...
Re: Another Powderpost beetle problem A message posted at WOODWEB's Sawing and Drying Forum (5/29) -- I just had a lift of material fumigated for PPB. I had the convenience of driving a t ...
Very small batch to dry (two boards) A message posted at WOODWEB's Sawing and Drying Forum (3/29) -- I have two slabs of 10/4 Ambrosia Maple that I need to dry quicker than air drying. A ...
Re: Dry 3 Inch Red Oak A message posted at WOODWEB's Sawing and Drying Forum (3/29) -- Air drying could do a lot of damage if not done carefully. It is safer to put in a we ...
Re: kiln drying old heart pine A message posted at WOODWEB's Sawing and Drying Forum (3/29) -- Thanks Tim, it is a 4'X4'X10' plywood with a 4 inch shell if r24 insulation and vapor ...
Re: burning wood scraps A message posted at WOODWEB's Sawing and Drying Forum (1/29) -- With my Heatmore and Woodmaster outdoor wood burners, and most brands to my knowledge ...
Re: Using tobacco kiln to dry lumber? A message posted at WOODWEB's Sawing and Drying Forum (12/28) -- this is just my thought, the wood will smell like tobacco ? i don't smoke and can't ...
Re: How long to heat to sterilize wood A message posted at WOODWEB's Sawing and Drying Forum (8/28) -- What species of wood? What insect did you have in the wood? Was the wood kiln dried a ...
worms in pine A message posted at WOODWEB's Sawing and Drying Forum (6/28) -- I am a bit stumped as I did not think this was suppose to happen in dry wood. In 2011 ...
Re: Drying wood in a tropical climate A message posted at WOODWEB's Sawing and Drying Forum (5/28/22) -- It is best to rely on past tests and information. Concrete is not used for a kiln ...
Re: Drying wood in a tropical climate A message posted at WOODWEB's Sawing and Drying Forum (5/28/22) -- It is best to rely on past tests and information. Concrete is not used for a kiln ...
Re: Live Oak Sandbox - Rot Resistance and Drying A message posted at WOODWEB's Sawing and Drying Forum (5/28/22) -- #1. Does not matter from a decay point of view. #2. There are safe ways to kiln dr ...
Plants to plant to discourage insects A message posted at WOODWEB's Sawing and Drying Forum (4/28) -- Is there a plant such as rosemary, lavender, etc. that I can plant around my lumber y ...
Kiln Drying Workshop A message posted at WOODWEB's Sawing and Drying Forum (12/27) -- We are holding our Annual Kiln Drying Workshop at SUNY ESF January 8-11, 2018 in Syr ...
Steaming for the purpose of conditioning. A message posted at WOODWEB's Sawing and Drying Forum (11/27) -- Recently found a good cheap source for air dried white oak, so I have been steam ben ...
Re: Steaming for the purpose of conditioning. A message posted at WOODWEB's Sawing and Drying Forum (11/27) -- Conditioning lumber is a process at the end of kiln drying to reduce stress. Your us ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- I'd definitely go for kiln-dried. My major concern with having it air dries is the sa ...
Re: fan reversals A message posted at WOODWEB's Sawing and Drying Forum (9/27) -- Conditioning (relief of stresses) is affected by how fast you can add moisture back a ...
Measuring Wood Whiteness A message posted at WOODWEB's Sawing and Drying Forum (1/27) -- Does anyone have experience measuring the whiteness of kiln dried lumber? Drying whit ...
Pre-dryer??? A message posted at WOODWEB's Sawing and Drying Forum (1/27) -- Boss has got this idea about re-engineering our t-sheds we use for air drying. Instal ...
Ambrosia MAple A message posted at WOODWEB's Sawing and Drying Forum (11/26) -- A colleague of mine asked about some ambrosia maple that has been kilned dried, but ...
fan reversals A message posted at WOODWEB's Sawing and Drying Forum (9/26) -- We have our kiln fans set to reverse every 2 hours. i was considering lowering the re ...
Re: milling quartered red oak A message posted at WOODWEB's Sawing and Drying Forum (7/26) -- The quartered logs will take several years to reach air dry (around 14% moisture cont ...
Re: milling quartered red oak A message posted at WOODWEB's Sawing and Drying Forum (7/26) -- Hey Andy, Though I don't know the answer to your question, I do know that the Doc and ...
Re: Sawing and drying grown crooks A message posted at WOODWEB's Sawing and Drying Forum (3/26) -- So what happens if it does move? Will it take it out of the game if it moves an inch? ...
Re: Finally going to build a Solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/26) -- Thanks Gene, I found this on a technical page. "It is not recommended for applic ...
Re: drying hickory A message posted at WOODWEB's Sawing and Drying Forum (2/26/23) -- You didn't hurt anything. The oil may slow the drying down a little but not much. ...
Re: southeastern kiln club A message posted at WOODWEB's Sawing and Drying Forum (2/26) -- I would expect about 35 people will attend. Certainly a few will be similar to you. ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/26) -- I forgot the roof too...it will be 10' roughly. ...
burning wood scraps A message posted at sawdry (12/31) -- I have two outdoor woodburners with forced air draft to heat my shop I notice that the kiln dried wood scraps o ...
Looking for high temp thermostat A message posted at WOODWEB's Sawing and Drying Forum (1/26) -- I'm starting on construction on my building for my new Nyle kiln. I'm adding a heat e ...
Re: 8/4 red oak A message posted at WOODWEB's Sawing and Drying Forum (12/25) -- You will find that 8/4 oak can check and honeycomb on the air yard even in the winte ...
Re: RE: Hot box to dry wood A message posted at WOODWEB's Sawing and Drying Forum (11/25) -- Drying wood takes a lot more than just heating it. You'll have to give some details ...
RE: Hot box to dry wood A message posted at WOODWEB's Sawing and Drying Forum (11/25) -- We have a hot box that we used to dry wood like a kiln, which is 4 ft. x 4 ft. x 8 f ...
Re: Using old wood for new projects? A message posted at WOODWEB's Sawing and Drying Forum (10/25) -- Gene, Is it possible to still have beetles in wood if there are no visible holes on ...
Re: Question on Bug kill drying A message posted at WOODWEB's Sawing and Drying Forum (8/25/24) -- RichC, I took your advice and purchased a thermocouple and some 13'cables so I can ...
Dehumidifier or AC? A message posted at WOODWEB's Sawing and Drying Forum (5/25) -- For a relatively small-size kiln, what do you think is better, a dehumidifier, or an ...
Kiln Drying of Hardwood Lumber Short Course A message posted at WOODWEB's Sawing and Drying Forum (5/25) -- This is a reminder that Penn State Extension will be holding a Kiln Drying of Hardwoo ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (4/25/22) -- Johnson controls makes temp controllers. I got mine for $65. For temp monitoring a ...
Re: New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (2/25/23) -- Yes, Sir I do, but for the life of me, I cannot understand the math equations. ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/25) -- There will be three pieces that are about 10' long--the floor, the front wall and the ...
Re: Drying 8/4 white oak A message posted at WOODWEB's Sawing and Drying Forum (1/25/24) -- Thanks guys, the kiln manual says I can hit the load hard if air dried to < 20% ...
Re: Drying 8/4 white oak A message posted at WOODWEB's Sawing and Drying Forum (1/25/24) -- Hey Jeff - Tinker with the kiln settings, make sure the air is flowing smoothly, a ...
Re: Table Top and Skirt Shrinkage A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- Thank you for the prompt response and the kiln vs. air dry. I realize that the physic ...
Re: DRYING 8/4 SLABS A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- thanks gene. I pulled the book out of my desk and gave it a look. the mill has cut ab ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- Thanks Gene!!! Shoot me a link if you have it on the reference to the egyptian gluing ...
Re: Drying Black Spruce dead straight A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- Well at last I am loading the spruce into the dry kiln (Nyle L200). Is there concern ...
Re: Drying a large slab of sugar maple A message posted at WOODWEB's Sawing and Drying Forum (10/24) -- I hope you have coated the end grain with anchorseal already. It is most effective w ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/24) -- Where is the best position to vent some of the heat from my dh kiln. It is way too ho ...
Finally going to build a Solar kiln A message posted at WOODWEB's Sawing and Drying Forum (3/24) -- Due to limited space out on my parking lot here at the shop in LR AR. I need to make ...
Re: 8/4 W. Oak R+Q A message posted at WOODWEB's Sawing and Drying Forum (2/24) -- It needs to be drier. Note that when you plane or mold it, you will expose the wetter ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/24) -- Dr. Gene - no need to reply. Mark Hedin from the school contacted me. No camper this ...
Re: cutting A message posted at WOODWEB's Sawing and Drying Forum (2/24) -- After you cut them, they need to be equalized because the moisture content in center ...
Re: Drying 8/4 white oak A message posted at WOODWEB's Sawing and Drying Forum (1/24/24) -- Something similar happened to me years ago. I was told the lumber was "case h ...
8/4 red oak A message posted at WOODWEB's Sawing and Drying Forum (12/23) -- Hi all. We are thinking of cutting 8/4 red oak. Its december and our plan is put it ...
Re: acclimating lumber A message posted at WOODWEB's Sawing and Drying Forum (11/23) -- You are not acclimating lumber, you are trying to kiln dry it. Of course you need he ...
defect in select white oak KD A message posted at WOODWEB's Sawing and Drying Forum (10/23) -- We have been re sawing some 6/4 and 8/4 select KD rift white oak and we are seeing a ...
Re: Channeled Sticker Manufacturers A message posted at WOODWEB's Sawing and Drying Forum (9/23) -- I am looking for people who can recommend a kiln stick from a supplier they personall ...
Re: kiln roof A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- The double wall is essential for good performance. It makes 50% faster drying and bet ...
Re: Dehumidification kiln choice A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- Thank you for the info. My Nyle 200m is on its way. Excited to get started. ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- Thank you for responding.The camphor laurel was reasonably fresh from the mill. I hav ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- If the core is 32% and the shell is 6% MC, then you could have an average of 20% MC. ...
Re: stairway I built from my homemade mill A message posted at WOODWEB's Sawing and Drying Forum (7/23) -- Rod, Your enthusiasm and what you have done with your mill are great. But I think wha ...
NEKDA May 2-3 A message posted at WOODWEB's Sawing and Drying Forum (4/23) -- Our New England Kiln Drying Association Spring Meeting is May 2 & 3 in Sayre, PA. ...
Re: "off the stump" moisture content A message posted at WOODWEB's Sawing and Drying Forum (4/23) -- I looked in the dry kiln operator manual and it's showing the same MC as the original ...
Dry Kiln Short Course A message posted at WOODWEB's Sawing and Drying Forum (4/23) -- Penn State Extension will be holding a Kiln Drying of Hardwood Lumber short course on ...
Re: Oak drying A message posted at WOODWEB's Sawing and Drying Forum (4/23) -- i suggest air drying carefully first...open shed. This would be no less than 120 days ...
Stacking sticks A message posted at WOODWEB's Sawing and Drying Forum (3/23/22) -- We operate a manufacturing plant for custom wood flooring. On site we have a small ...
Milling A message posted at WOODWEB's Sawing and Drying Forum (3/23/22) -- I've been milling up Black walnut for the past year after buying a Woodmizer. I st ...
8/4 W. Oak R+Q A message posted at WOODWEB's Sawing and Drying Forum (2/23) -- We just got a load of 8/4 W. Oak R+Q in from a customer. We did an oven dry on the co ...
Advance Kiln Drying Workshop- March 11, 2015 A message posted at sawdry (12/31) -- Penn State Extension in partnership with the Keystone Kiln Drying Association will be offering an Advanced Lumb ...
Re: Drying Red OAK 4X6 Green Wood A message posted at WOODWEB's Sawing and Drying Forum (1/23) -- Thanks Tim! I agree, you need proper joinery no matter what kind of project you are w ...
Re: Numbers divided by a slash? 4/4, 5/4 etc... A message posted at WOODWEB's Sawing and Drying Forum (1/23) -- Let me add a bit more to the discussion. For hardwood lumber, 4/4 means that the thic ...
Older moisture meters-are they a good choice? A message posted at WOODWEB's Sawing and Drying Forum (1/23) -- I am looking at a couple of older Delmhorst moisture meters on ebay, one is a DC-3 an ...
Re: DRYING 8/4 SLABS A message posted at WOODWEB's Sawing and Drying Forum (1/22) -- Some species dry so much differently than other species that we do not mix them in a ...
Re: hygrometers A message posted at WOODWEB's Sawing and Drying Forum (1/22) -- I believe you a are looking for a traditional wet-bulb and dry-bulb device. These are ...
Re: kiln roof A message posted at WOODWEB's Sawing and Drying Forum (8/21) -- It's a insulation purpose to help keep from losing the temp achieved during the dayli ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/21) -- Heinrich, Any of the softwoods or hardwoods with lower specific gravities (say around ...
Re: First solar kiln load results A message posted at WOODWEB's Sawing and Drying Forum (5/21/25) -- Your detailed tracking and sample-based MC analysis was helpful to read—especially ...
Making a cut to avoid cracking A message posted at WOODWEB's Sawing and Drying Forum (3/21) -- Dear all, I am intend to replace a wall with an European Oak beam of 25cm square and ...
Great Lakes Kiln Meeting April 24-25 A message posted at WOODWEB's Sawing and Drying Forum (3/21) -- The Great Lakes Kiln Drying Association will hold their spring meeting April 24 & ...
Re: Eastern white pine for projects A message posted at WOODWEB's Sawing and Drying Forum (12/20) -- If you don't care about a customer calling you about piles of frass on the floor, th ...
Re: good planers A message posted at WOODWEB's Sawing and Drying Forum (12/20) -- We'll all I can tell you about are Woodmaster planers. My son is building a house, 1 ...
Re: PPB fungus A message posted at WOODWEB's Sawing and Drying Forum (11/20) -- The hole you see is the exit hole. An egg is laid, the larva forms and works it's wa ...
Re: PPB fungus A message posted at WOODWEB's Sawing and Drying Forum (11/20) -- I understand all that. I rive my stock, shave it with a drawknife following the grai ...
milling quartered red oak A message posted at WOODWEB's Sawing and Drying Forum (7/20) -- i was curious on the drying time on 24 inch diameter red oak that was quartered a yea ...
Re: milling spalted maple and pecan A message posted at WOODWEB's Sawing and Drying Forum (6/20) -- Milling the pecan and maple are no different than other species. Your trouble with th ...
Re: mc of core/shell and equilizing A message posted at WOODWEB's Sawing and Drying Forum (6/20) -- OK. So the core and the shell will equalize during the final? And will continue to eq ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/20) -- I love the organic shape of the bench. I hope it has straight grain with few knots (o ...
New facility and beetles A message posted at WOODWEB's Sawing and Drying Forum (2/20/23) -- After 16 years in business on family property we have the opportunity to relocate ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (2/20) -- Kiln dried wood is typically prized for it's stability and use in construction. This ...
Re: Large Scale Drying A message posted at WOODWEB's Sawing and Drying Forum (12/19) -- Thanks for the advice. We'll see. As for the cutting and sawing, nails and whatnot - ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (11/19/22) -- Some wood suppliers prefer air drying because the process dries out the logs even ...
milling spalted maple and pecan A message posted at WOODWEB's Sawing and Drying Forum (6/19) -- Hello, I have a small tree service, and have removed a large pecan from a customers y ...
mc of core/shell and equilizing A message posted at WOODWEB's Sawing and Drying Forum (6/19) -- according to kiln dryers operation manual the instructions for equalizing say to star ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/19) -- If you really want to do this, with the least headaches, you should go at it while it ...
Re: Dehumidification H20 output monitoring A message posted at WOODWEB's Sawing and Drying Forum (4/19) -- That's how I did it with my homebuilt dehumidification kiln. I ran a hose from the de ...
Re: New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (3/19/23) -- Not the advice you are after, but YouTube is always one of the places I would look ...
Re: Finishing an air dried stack A message posted at WOODWEB's Sawing and Drying Forum (3/19) -- If you cannot get the lumber to dry when the humidity in the kiln is under 30% RH, th ...
Re: Finishing an air dried stack A message posted at WOODWEB's Sawing and Drying Forum (3/19) -- So, I have tried all sorts of things to push the last 2.5% of water out of the lumber ...
Re: Reclaimed wood type and value? A message posted at WOODWEB's Sawing and Drying Forum (2/19) -- Is it off the house? Cedar and fir are extremely brittle at that age. Removing split ...
Stabilizing red oak with PEG 300 A message posted at WOODWEB's Sawing and Drying Forum (2/19) -- The bench I carved from a red oak log is 40 inches wide and 10 to 15 inches or more t ...
Re: Final stages in dh kiln A message posted at WOODWEB's Sawing and Drying Forum (1/19) -- You seem to have a great understanding of the EMC of air as related to the MC of wood ...
Re: Final stages in dh kiln A message posted at WOODWEB's Sawing and Drying Forum (1/19) -- When I said "increase the heat," usually you only heat it for four hours an ...
Re: Drying 8/4 Cypress A message posted at WOODWEB's Sawing and Drying Forum (1/19) -- In a good kiln, it can go in right away from a quality viewpoint. From a cost view po ...
Joining wet planks A message posted at WOODWEB's Sawing and Drying Forum (1/19) -- Is it possible to finger join wet-off-saw eucalyptus planks, that is for air-drying a ...
Drying/Sawing of Black Locust A message posted at WOODWEB's Sawing and Drying Forum (9/18) -- Since black locust has very little shrinkage and limit movement when is the best time ...
Re: Question A message posted at WOODWEB's Sawing and Drying Forum (9/18) -- I agree. 70% of the shipping weight will be slabs, sawdust & water. The ideal sit ...
Re: sulphur fumigation candles A message posted at WOODWEB's Sawing and Drying Forum (8/18) -- Lester, If your solar kiln gets the temp up to 135º to the core, you don't need anyth ...
Re: First solar kiln load results A message posted at WOODWEB's Sawing and Drying Forum (7/18) -- Gene, why does slow drying cause more cupping? I am a novice wood dryer. I have bough ...
Re: drying red elm A message posted at WOODWEB's Sawing and Drying Forum (6/18) -- Red elm is pretty tolerant and can be dried at the same rate as ash. With 8/4 stock t ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/18) -- Looking at the scale model, it seems a modification in design may make a large differ ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/18) -- Your design is YOUR design... stick with it.. get it done, see what happens to it as ...
Re: drying bamboo A message posted at WOODWEB's Sawing and Drying Forum (3/18) -- Round tubes. Started the DH kiln at 100 degrees and everything seems fine. ...
Re: when to saw blackwallnut A message posted at WOODWEB's Sawing and Drying Forum (3/18) -- Not only saw ASAP, but get it stacked and stickered for air drying as it comes off th ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/18) -- If the TDAL is zero, then the air is providing no energy so there is no drying. I sus ...
Drying 8/4 Slabs A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- i may be needing to dry a mixed load of live edge slabs. the speices mentioned to me ...
Re: air drying ash A message posted at WOODWEB's Sawing and Drying Forum (1/18) -- I agree. The conditions is Ohio will not dry under 12% MC, but for furniture, cabinet ...
Eastern white pine for projects A message posted at WOODWEB's Sawing and Drying Forum (12/17) -- Good evening to all. I have a skid of two by 4s and two by 8s of eastern white pine ...
Kiln Drying Workshop - Syracuse A message posted at WOODWEB's Sawing and Drying Forum (12/17) -- We are again holding our Annual Kiln Drying Workshop at SUNY ESF January 7-10, 2019 ...
Re: Large Scale Drying A message posted at WOODWEB's Sawing and Drying Forum (12/17) -- Thanks. We hadn't thought of vacuum drying but that would be interesting. Rather tha ...
Re: Large Scale Drying A message posted at WOODWEB's Sawing and Drying Forum (12/17) -- I can't think of anyone drying large Soft Maple squares but we have several customer ...
Paul Bois, National Drying Specialist A message posted at WOODWEB's Sawing and Drying Forum (9/17) -- Paul Bois, 89, died peacefully in Madison, WI on September 9. Paul was director of th ...
sulphur fumigation candles A message posted at WOODWEB's Sawing and Drying Forum (8/17) -- Just read about using this to get read of PP and wanted to ask can this be used in th ...
Re: DH kiln drying douglas fir beams and posts A message posted at WOODWEB's Sawing and Drying Forum (7/17) -- I hope you studied this out prior to such a large purchase.....Large beams aren't fea ...
Re: kiln help A message posted at WOODWEB's Sawing and Drying Forum (1/17) -- I do this as part of the services from my company, The Wood Doctor’s Rx LLC. ...
Re: specific gravity/ wagner mmc220 A message posted at WOODWEB's Sawing and Drying Forum (12/16) -- Thanks for the input. I have been trying to post a response, but after pressing post ...
Wood-Mizer VK2000 kiln control unit A message posted at WOODWEB's Sawing and Drying Forum (10/16/26) -- I'm looking for a control unit for a Wood-Mizer VK2000 preferably working, but no ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/16) -- Mark, As you can see from the attached scale model, of course I complicated the issue ...
Re: 7/4 Red Oak Redry A message posted at WOODWEB's Sawing and Drying Forum (4/16/26) -- Red oak is already tricky enough the first time around, so redrying it two years l ...
Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/16) -- I've been drying with 2 new package kilns for the last 9 months, and as the supply of ...
Re: Drying 5/4 White Oak, TDAL won't equalize A message posted at WOODWEB's Sawing and Drying Forum (2/16) -- Measuring TDAL is extremely difficult Ina hardwood kiln. So, my first guess is that t ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/16) -- Hi, Gene. Sounds interesting. I'll try to make it over there. Great photo of you & ...
Re: Final stages in dh kiln A message posted at WOODWEB's Sawing and Drying Forum (1/16) -- Thank you Dr. Wengert. I've been trying to follow the Nyle conservative schedule for ...
Re: specific gravity/ wagner mmc220 A message posted at WOODWEB's Sawing and Drying Forum (12/15) -- The density that the Wagner meter uses is the green density. You do not adjust this ...
Re: new dry kiln on the cheap A message posted at WOODWEB's Sawing and Drying Forum (12/15) -- Ha! I guess it won’t work anymore then. My wife was also impressed with my design. ...
Re: Drying A message posted at WOODWEB's Sawing and Drying Forum (12/15) -- Interesting... i had the same question about using a greenhouse as a solar kiln. Wou ...
Re: when can we use white oak? A message posted at WOODWEB's Sawing and Drying Forum (12/15) -- 30 days? More like a couple of years. No species of wood will be ready to be used by ...
moisture, heat and lignin A message posted at WOODWEB's Sawing and Drying Forum (11/15) -- My question has to do with heat and it's effect on lignin. Background: I make Windso ...
130 deg. for how long to kill bugs in 2x Red Oak? A message posted at WOODWEB's Sawing and Drying Forum (11/15) -- I may set up a solar kiln by my wood shop. I can add extra elements for the 130 deg. ...
Vacuum Drying Workshop A message posted at WOODWEB's Sawing and Drying Forum (10/15) -- VA Tech will be holding a workshop on vacuum dry kilns on December 4th. Please look ...
a random prong test A message posted at WOODWEB's Sawing and Drying Forum (8/15) -- we've had these few hard maple boards that sitting on the wall in the grading station ...
Re: First solar kiln fans detail A message posted at WOODWEB's Sawing and Drying Forum (7/15) -- I used three Lasko 20 inch fans, and made individual fan mounts. With the roof lifted ...
Re: Drying Black Spruce dead straight A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- The conditioning EMC for softwoods is target MC + 3. This is a fairly high EMC as the ...
Re: Drying Black Spruce dead straight A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- Ok, thankyou again Gene. So with a final target MC of 9 or 10%, at what point do I st ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- Heinrich, One possibility to accelerate the dryinig process and to reduce cracking is ...
Red, White Oak Air drying shrinkage time? A message posted at WOODWEB's Sawing and Drying Forum (6/15) -- First time bandsaw mill owner/user. Building 2 pole barns from red or white oak. (Don ...
Re: Cool down times???? A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- What problem are you trying to correct by letting the kiln cool down? Your prong test ...
Re: Cool down times???? A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- So does that mean that the prongs shouldn't be tested until a few days after conditio ...
Re: New Sawyer w/new solar kiln needs help A message posted at WOODWEB's Sawing and Drying Forum (3/15/23) -- Xiaomi smart temperature and humidity meter has a soft price but a lot of outstand ...
Re: Final stages in dh kiln A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- Any chance you can increase the DB, but still keep 5% EMC? Heat will help the moistur ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- Catalog would never download... went to site to find it.. http://www.marcadams.com/av ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- Thanks for the faster link...the slower link includes lots of pictures for all the cl ...
ash sawmill A message posted at WOODWEB's Sawing and Drying Forum (1/15) -- hi guys. i just wanna take some information about ash sawmill. i m coming to columbus ...
Re: specific gravity/ wagner mmc220 A message posted at WOODWEB's Sawing and Drying Forum (12/14) -- Hi Nathan. I have the same meter that basically measures density. it could just give ...
Re: new dry kiln on the cheap A message posted at WOODWEB's Sawing and Drying Forum (12/14) -- What happens when you need to use those windows for another project? ...
Re: Dehumidification kiln choice A message posted at WOODWEB's Sawing and Drying Forum (8/14) -- Another advantage of NYLE is that there are hundreds of people that can tell you how ...
Re: Air drying Cherry A message posted at WOODWEB's Sawing and Drying Forum (7/14/23) -- Not being kiln dried and not sterilized, you are asking for disaster when the proj ...
Re: Resawing air dried black walnut A message posted at WOODWEB's Sawing and Drying Forum (5/14) -- Do you detect any cupping or other warping at this point? Determining moisture gradie ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/14/22) -- John That oil filled radiator can get up to 150 degrees? It takes a lot of heat to ...
Re: waves and rip saw A message posted at WOODWEB's Sawing and Drying Forum (1/14) -- Without pictures, I can only imagine what you are talking about. I think that you eit ...
specific gravity/ wagner mmc220 A message posted at WOODWEB's Sawing and Drying Forum (12/13) -- I am wondering if anyone can shed some light on specific gravity settings on Wagner ...
Large Scale Drying A message posted at WOODWEB's Sawing and Drying Forum (12/13) -- We have a need for large square molding blanks, 17/4 or thereabouts later to be mill ...
Re: Wood-Mizer VK2000 kiln control unit A message posted at WOODWEB's Sawing and Drying Forum (11/13/26) -- Can you check with Sawblade.com? They carry parts for a lot of saws. Sorry if thi ...
Re: homade dry kiln heat source A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- A process that is called heated room drying is used for drying eastern red cedar to ...
Re: homade dry kiln heat source A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- That's not hot enough to sterilize the wood. You're going to need 150 degrees after ...
Kiln drying meeting, Nov 1&2, Ohio A message posted at WOODWEB's Sawing and Drying Forum (10/13) -- The Ohio Lumber Drying Association (DA), the Keystone Kiln DA, the Allegheny DA, and ...
Moisture Content of lumber A message posted at sawdry (12/31) -- I know this may be too broad a question but what is the moisture content you all are shooting for in a new deli ...
Re: Dehumidification kiln choice A message posted at WOODWEB's Sawing and Drying Forum (8/13) -- I am a little biased because I started Nyle in 1977 and sold the business some time a ...
Re: how long to dry oak for barn construction A message posted at WOODWEB's Sawing and Drying Forum (8/13) -- Hey Eric, I've got a similar project ahead of me usin' green Red Oak (Board and Batt. ...
Avoiding Stain in Hickory A message posted at WOODWEB's Sawing and Drying Forum (5/13) -- Hi All! I am buying a truckload (10MBF) of top grade 4/4 Hickory. The logs will be sa ...
Re: Cooking green wood in linseed oil A message posted at WOODWEB's Sawing and Drying Forum (2/13) -- Keith, thank you for you comments. I love your wild life and nature photography, beau ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (1/13) -- A vacuum kiln delivers pure white HM. Even SM comes out as white. I once saw a custom ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (1/13) -- You are right, Gene. I should have said "our" kilns but I didn't want to bo ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (1/13) -- It appears that vacuum kilns are used for small pieces of wood. I couldn't find 8 foo ...
Re: sticker eastern red cedar? A message posted at WOODWEB's Sawing and Drying Forum (10/12/22) -- Never heard of any species that will go from green to dry in a week, unless it's ...
Re: Drying/acclimating? A message posted at WOODWEB's Sawing and Drying Forum (8/12) -- Oftentimes, a home at this time of year will be at 9% EMC. So, the wood in several mo ...
Re: splits in large slabs A message posted at WOODWEB's Sawing and Drying Forum (6/12) -- Den had to call my attention to the location of the pith in that slab. My comments ar ...
EBAC Control unit A message posted at WOODWEB's Sawing and Drying Forum (3/12) -- I have a 10 - 12 year old EBAC kiln, LD 3000. The control unit (UC-2) no longer funct ...
Re: River Birch mill thickness prior to kiln dry A message posted at WOODWEB's Sawing and Drying Forum (2/12) -- Just some thoughts. I'm not familiar with River Birch at all. If your table is going ...
Re: newby sawyer, more questions. A message posted at WOODWEB's Sawing and Drying Forum (2/12) -- Yes Dave it does help, thanks for taking the time to respond. What you said makes sen ...
Re: River Birch mill thickness prior to kiln dry A message posted at WOODWEB's Sawing and Drying Forum (2/12) -- If stock wants to cup, thickness is not going to limit that. If you like Viking looki ...
Re: secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/12) -- Gene, it is truly great seeing you at work, dispensing wisdom and great advise and al ...
Re: Wax and Wood A message posted at WOODWEB's Sawing and Drying Forum (1/12) -- Thanks Mark. Heat is always an issue from May thru Nov. All of our wood in the past h ...
Re: new dry kiln on the cheap A message posted at WOODWEB's Sawing and Drying Forum (12/11) -- Here are some pictures ...
Re: wood kiln A message posted at WOODWEB's Sawing and Drying Forum (10/11/23) -- How would you ever get that heat all through the stack when the floor is covered ...
Re: Drying wood prior to using kilns? A message posted at WOODWEB's Sawing and Drying Forum (8/11) -- What encourages blue stain is slow drying in warm weather. The risk of blue stain in ...
Drying/acclimating? A message posted at WOODWEB's Sawing and Drying Forum (8/11) -- I have quarter sawn red oak planks 4/4, 6" to 10" in width, that I have dri ...
Drying Black Spruce dead straight A message posted at WOODWEB's Sawing and Drying Forum (7/11) -- I am getting into arrowshaft production for the archery industry. I plan to saw, air- ...
Re: Drying slab locust from a stump A message posted at WOODWEB's Sawing and Drying Forum (6/11) -- Latex paint is designed to allow more moisture loss than what you want. Log sealer is ...
Green logs for furniture A message posted at WOODWEB's Sawing and Drying Forum (4/11/22) -- I want to start cutting random logs left behind from tree service and storms. I ha ...
Re: Finishing an air dried stack A message posted at WOODWEB's Sawing and Drying Forum (3/11) -- I suspect you have moisture meter issues. The air dried stack at 12% is normal. But i ...
Re: River Birch mill thickness prior to kiln dry A message posted at WOODWEB's Sawing and Drying Forum (2/11) -- Perfect, very helpful. Thank you Guy cutting tree down says he has a mill and can do ...
Re: Sinker Log Process Help A message posted at WOODWEB's Sawing and Drying Forum (10/10) -- Ignore sinkrswim.. did not even use his real name... No personal experience with sin ...
Re: 21% MC in blue pine stair treads A message posted at WOODWEB's Sawing and Drying Forum (9/10) -- We have a better calculator for shrinkage and other items too here at WoodWeb. Look a ...
Re: Drying wood prior to using kilns? A message posted at WOODWEB's Sawing and Drying Forum (8/10) -- My Great-Great Uncle owned a lumber yard in Emden, IL. It is still family owned, but ...
Re: Drying wood prior to using kilns? A message posted at WOODWEB's Sawing and Drying Forum (8/10) -- I should have added this picture of the Emden Lumber Co, before my Great-Great Uncle ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/10) -- I have the window Air conditioner up and running in the kiln, my output has doubled t ...
Re: drying red elm A message posted at WOODWEB's Sawing and Drying Forum (6/10) -- You could air dry to get the moisture content down, but I would definitely finish dry ...
RE: Table Making-- Best Method A message posted at WOODWEB's Sawing and Drying Forum (5/10) -- To make a 4-foot wide table, primarily out of oak or maple, is it better to glue 2 or ...
Re: First solar kiln load results A message posted at WOODWEB's Sawing and Drying Forum (5/10) -- Cupping of wide pieces with the pith in or near is next to impossible. It is a natura ...
Re: honey comb in walnut A message posted at WOODWEB's Sawing and Drying Forum (4/10) -- Looks like the lumber was dried way too quickly. Was that purchased from a commercial ...
Re: supplemental heat for solar kiln to kill bugs A message posted at WOODWEB's Sawing and Drying Forum (1/10/22) -- Have you ever gone on The Forestry Forum? It gets discussed there quite often. One ...
Re: Need to heat dry 57 Pieces of Teak A message posted at WOODWEB's Sawing and Drying Forum (12/9) -- Most of the small kiln operators do not deal with certificates for export. You may no ...
pine/spruce stakes A message posted at WOODWEB's Sawing and Drying Forum (12/9) -- we currently manufacture stakes out of kd spf dimension lumber. we are considering sw ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/9) -- IF your using a window air conditioning for the DHing (I've not heard of a kiln using ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/9) -- I already have a heat source in the kiln, the airconditioner gives out more heat than ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/9) -- I appreciate all the advice, I am going to open up the kiln and add a 45° angle when t ...
Re: drying doug fur lumber A message posted at WOODWEB's Sawing and Drying Forum (7/9/22) -- it is close but of coarse at lower temps. because this kiln will only go to 150 f ...
Re: Live edge slabs, is the hype real? A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- My $0.02 is a lot of it depends on your market. The more urban your are the more likel ...
Re: Live edge slabs, is the hype real? A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- I can get it kiln dried for about 3 $ a bd ft. Never have . Have worked some 2 inch af ...
Re: Recommendations for solar kiln controls A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- Your idea about temperature for turning on the fans is indeed good. However, you could ...
Re: Recommendations for solar kiln controls A message posted at WOODWEB's Sawing and Drying Forum (5/9) -- If you heat foggy air by about 25 F, the humidity drops under 30% RH. Less heat does d ...
Re: secondary heat source for solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/9) -- Thank you to both of you for your wisdom. I buy timber for a local mill and know loggi ...
Re: Cutting Slabs A message posted at WOODWEB's Sawing and Drying Forum (11/8) -- FWIW I haven't had good luck drying sycamore, some real problems but the tree was ver ...
Re: Storing KD timber outside A message posted at WOODWEB's Sawing and Drying Forum (9/8) -- Why would you put a barrier in the roof if there are no walls? You will have to sticke ...
21% MC in blue pine stair treads A message posted at WOODWEB's Sawing and Drying Forum (9/8) -- I'm having thick blue pine ponderosa stair treads milled for a metal stairway ( 5 1/2& ...
Re: Drying SYP Timbers for Transport A message posted at WOODWEB's Sawing and Drying Forum (6/8/25) -- Really good question — I’ve faced similar challenges with larger SYP timbers. Using ...
Re: Live edge slabs, is the hype real? A message posted at WOODWEB's Sawing and Drying Forum (5/8) -- Everybody is selling live edge slabs, even Woodcraft. $4-$6 is a bargain for kiln drie ...
Wood Boring Insect Larva Prevention A message posted at WOODWEB's Sawing and Drying Forum (5/8) -- Does anyone have any suggestions or recomendations for the prevention of PPB and other ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/8/22) -- Yea, unfortunately i have no experience with this other than with pine and hemlock ...
Re: Transporting Sawn Ash A message posted at WOODWEB's Sawing and Drying Forum (4/8) -- But is kiln dried allowed ? ...
Re: Need advice about my bookmatched quilted maple A message posted at WOODWEB's Sawing and Drying Forum (4/8) -- TN Tim has indeed stated the main issues. If you can find someone in your area that kn ...
Re: How long can logs sit before milling? A message posted at WOODWEB's Sawing and Drying Forum (3/8) -- Casehardening isn't caused from logs sitting on the yard.....it's from incorrect kilni ...
Re: southeastern kiln club A message posted at WOODWEB's Sawing and Drying Forum (3/8) -- I email Phil Mitchell and he told me that in Oct. there will be a 2 day DH short cours ...
Walnut Water pockets A message posted at WOODWEB's Sawing and Drying Forum (2/8) -- I dried a load of 10/4 walnut slabs recently and found that the MC % was all over the ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (1/8) -- It is a long story, but basically the wood was air dried, giving a white color to the ...
Re: homade dry kiln heat source A message posted at WOODWEB's Sawing and Drying Forum (12/7) -- It drops the moisture kind of fast.. so there is a checking issue. I am going to run ...
Re: Free Webinar, 8/26/2020 Drying oak And Maple A message posted at WOODWEB's Sawing and Drying Forum (9/7) -- Understand that the Lyctid PPB has a life cycle of a year or longer. The holes you see ...
Kentucky Coffee Tree A message posted at sawdry (12/31) -- I'm preparing to run a partial charge of Kentucky Coffee Tree lumber through my kiln Can't find any info as far ...
Question on Bug kill drying A message posted at WOODWEB's Sawing and Drying Forum (8/7/24) -- I would like to ask for an opinion, and I know saying ( it’s like an Axx xxxx every ...
Heat Treating 6" X 8" pine house logs A message posted at WOODWEB's Sawing and Drying Forum (5/7) -- Hello Everyone I was unable to get the logs and lumber into the dry kiln for proper tr ...
Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (4/7/22) -- Hi, I've decided to make the plunge to drying my own lumber. I plan to build my own ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/7/22) -- Yea, unfortunately i have no experience with this other than with pine and hemlock ...
Re: sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/7/22) -- Please do the forum a favor and post photos of the cants sawn prior to the kiln and ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/7) -- Mark B's response bring to mind two questions, If you have a 1” diameter hole drilled ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/7) -- It is species specific. It depends on the temperature. It depends on the length of tim ...
Re: New kid on the block A message posted at WOODWEB's Sawing and Drying Forum (4/7) -- Im the new kid on the block, and Im just amazed at all the information on here. Woow.! ...
Re: air drying ash A message posted at WOODWEB's Sawing and Drying Forum (4/7) -- Wayne I am in Ontario, so weather kind of similar. You won't get much drying over the ...
Lumber Drying Workshop at EXPO Richmond A message posted at WOODWEB's Sawing and Drying Forum (2/7/24) -- Virginia Tech and North Carolina State have joined up to provide a lumber drying wo ...
Re: White Hard Maple is Off Color A message posted at WOODWEB's Sawing and Drying Forum (2/7) -- Bruce, I see from your website you're in WI. I would have thought you could have found ...
Re: drying to single digits p2 A message posted at WOODWEB's Sawing and Drying Forum (1/7) -- I run my home built dehumidification kiln at 110F and follow a drying schedule like sh ...
Re: Looking for small kiln controller A message posted at WOODWEB's Sawing and Drying Forum (11/6/23) -- In case someone is interested in controllers. AC Infinity controller is WiFi, so c ...
Re: Remove bark before or after drying large slabs A message posted at WOODWEB's Sawing and Drying Forum (11/6) -- Jodi, I dry large slabs like your walnut here in Western Oregon, so have some experie ...
Can I use radiator fans? A message posted at WOODWEB's Sawing and Drying Forum (9/6/23) -- Can I go to the junk yard and get radiator fans that I can connect to my car batter ...
Re: Sterilizing reclaimed wood for kitchen. A message posted at WOODWEB's Sawing and Drying Forum (7/6) -- Kerosene heaters are not great heat sources. They can actually increase the humidity a ...
Live edge slabs, is the hype real? A message posted at WOODWEB's Sawing and Drying Forum (5/6) -- Are you sawyers out there really seeing a huge market for live edge slabs? I am locate ...
sawing a solid black walnut mantle A message posted at WOODWEB's Sawing and Drying Forum (4/6/22) -- Hi Folks! I’m getting ready to saw up a 10x6 solid black walnut mantle out of a log ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/6) -- Rich hit the nail on the head. The pegs need to be dry so when the timbers shrink they ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/6) -- thanks all for the feedback. The Wood Doctor gave the info I was specifically interest ...
drying bamboo A message posted at WOODWEB's Sawing and Drying Forum (3/6) -- Is there any info on kiln drying bamboo out there? Couldn't find much on the internet. ...
Re: Air Drying Holly A message posted at WOODWEB's Sawing and Drying Forum (3/6) -- Alcohol is not known as an effective way of stopping fungal growth in holly or any oth ...
Re: Kilns in West Michigan A message posted at WOODWEB's Sawing and Drying Forum (3/6) -- Derek, You may find the Kiln Drying section of our Sawing and Drying Directory to be o ...
Kilns in West Michigan A message posted at WOODWEB's Sawing and Drying Forum (3/6) -- Wondering if anyone out there knows of any Kilns to contract in West Michigan. ...
Drying maple cookies A message posted at WOODWEB's Sawing and Drying Forum (2/6) -- We have a very large DBH maple that we are wanting to cut into cookies for a project. ...
Re: Eastern white pine for projects A message posted at WOODWEB's Sawing and Drying Forum (1/6) -- Not to mention Eastern White Pine will bleed sap for the next 800 years if the pitch i ...
Re: Varying MC kiln dried red oak A message posted at WOODWEB's Sawing and Drying Forum (12/5) -- Higher density than assumed will result in higher %MC readings with pinless meters. A ...
Re: wood kiln A message posted at WOODWEB's Sawing and Drying Forum (11/5/23) -- No my thought is in winter months I would run floor heat to keep concrete warm and ...
Re: pine/spruce logs A message posted at WOODWEB's Sawing and Drying Forum (1/5) -- cut into "cants" an inch larger than you will need. Better to have sit in a ...
Re: 8/4 red oak A message posted at WOODWEB's Sawing and Drying Forum (1/5) -- So basically if Im correct the best way to dry red oak 8/4 is dead green right in the ...
Re: newby sawyer A message posted at WOODWEB's Sawing and Drying Forum (1/5) -- Thanks for your time guys, it means a lot. Where would be some good info on solar kiln ...
Kiln Drying Workshop - Jan 11-14, 2016 A message posted at WOODWEB's Sawing and Drying Forum (12/4) -- We are holding our Annual Kiln Drying Workshop at SUNY ESF January 11-14, 2016 in Syr ...
Re: oak tree drying /deck A message posted at WOODWEB's Sawing and Drying Forum (11/4) -- Saw them right away. Drying this time of year using normal air drying will take perha ...
Re: PPB worries A message posted at WOODWEB's Sawing and Drying Forum (4/4) -- Ash does make beautiful interior lumber if the logs are large enough and kiln drying c ...
Re: Thickness standard for 5/4? A message posted at WOODWEB's Sawing and Drying Forum (4/4) -- I'm in the boat with TT....I've cut logs with sapwood rotted off out of the woods, log ...
Re: Black Walnut Tree A message posted at WOODWEB's Sawing and Drying Forum (4/4) -- When you have it sawn, especially anything above the butt logs... saw them an inch or ...
Re: Don't Know How A message posted at WOODWEB's Sawing and Drying Forum (1/4) -- Hi, You will want to find local woodworkers who want to buy specialty wood like the th ...
Re: newby sawyer A message posted at WOODWEB's Sawing and Drying Forum (1/4) -- When you ask your customer, make sure you determine whether he/she is talking about gr ...
Re: drying to single digits A message posted at WOODWEB's Sawing and Drying Forum (12/3) -- I have a delmhorst J-2000 MC meter Doc so I'm set there. Also have a dehumidifier but ...
Re: drying to single digits A message posted at WOODWEB's Sawing and Drying Forum (12/3) -- The dehumidifier doesn't have to sit on the floor. Put it high enough so the water wi ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (11/3) -- Live oak must be air dried first. It cannot be dried fast. Elm and ash can dry quickl ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (11/3) -- What species and thickness? Generally top and bottom are open the same. Same for left ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (11/3) -- Making lumber from 1.25 in. Live oak, Pecan, Ash, and Elm. Have no experience drying ...
safe rate for moisture removal A message posted at WOODWEB's Sawing and Drying Forum (7/3) -- I read somewhere that the safe rate of moisture removal needs to be followed until you ...
How to kill bugs in an infested log....??? A message posted at sawdry (12/31) -- Hi guys I'm hoping someone can help me with this as it's a bit out of my wheelhouse My lumber usually comes in ...
Re: Another Powderpost beetle problem A message posted at WOODWEB's Sawing and Drying Forum (6/3) -- I can't give you info about air drying the 4" thick boards before putting them in ...
Re: drying hickory A message posted at WOODWEB's Sawing and Drying Forum (3/3/23) -- The one year per inch is not BS. It is not necessarily accurate all the time but it ...
Re: best wood for a slab cut on an old maple A message posted at WOODWEB's Sawing and Drying Forum (3/3) -- Hello Harlan, many specie will split in the center if you include the pith in your sla ...
defects A message posted at WOODWEB's Sawing and Drying Forum (2/3) -- hello there, I just have a quick question on causes of twist in kiln dried lumber. I r ...
How straight should 10/4 oak be after drying A message posted at WOODWEB's Sawing and Drying Forum (1/3) -- I just got in some 10/4 x random width x 14' kiln dried plain sawn red oak. Every boar ...
Green timber winter air drying A message posted at WOODWEB's Sawing and Drying Forum (12/2) -- Dear I have a furniture factory in romania and in August we started our own kiln dryi ...
Re: Solar drying fire wood to kill all insects A message posted at WOODWEB's Sawing and Drying Forum (10/2/23) -- It's not the moisture content that counts, it's the heat. The center of your piece ...
Re: worms in pine A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- The wood was kiln dried in about January of 2012 and the pitch set to 160° for several ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- Ken Your funny, not sure how you put a 2000 lbs piece of wood into a plastic bag with ...
Re: 40 inch diameter log in solar kiln A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- Vergil Leih dries turned tree trunks. He uses a micro wave oven he built. Basically pu ...
"smoked" oak A message posted at WOODWEB's Sawing and Drying Forum (6/2) -- Does anyone know the process or have any info on "smoked oak??? I believe it is d ...
"smoked" oak A message posted at sawdry (12/31) -- Does anyone know the process or have any info on smoked oak I believe it is done after it's been kiln dried in ...
Re: Twisted Maple Log A message posted at WOODWEB's Sawing and Drying Forum (3/2) -- I agree with Mark B that there will be a lot of reaction wood with the twisting growth ...
Re: solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/2) -- Sure, with a few design modifications to the collector and lots of insulation. ...
Re: Build your own solar kiln A message posted at WOODWEB's Sawing and Drying Forum (2/2) -- Correction: the capacity is 320 to 360 BF of 4/4 or 420 to 460 BF of 8/4. ...
Re: alberta spruce/pine A message posted at WOODWEB's Sawing and Drying Forum (1/2) -- Dehumidification is a good way to go in my biased opinion. It does cost something to r ...
drying to single digits A message posted at WOODWEB's Sawing and Drying Forum (12/1) -- I run into this problem every year. I purchase hardwood (particularly red oak) in the ...
Re: drying to single digits A message posted at WOODWEB's Sawing and Drying Forum (12/1) -- Then I'll need advice on how to build a small kiln (for ~100 ft). Can you point me in ...
Drying 5/4 quarter sawed white oak A message posted at WOODWEB's Sawing and Drying Forum (7/1) -- We have have some 5/4 quarter sawed white oak that we have been asked to dry. I though ...
drying pine A message posted at WOODWEB's Sawing and Drying Forum (6/1) -- Dr, Gene Would I have to be concerned about sticker stain on pine and spruce if I left ...
Kiln Drying Short Course July 19-21, 2016 A message posted at WOODWEB's Sawing and Drying Forum (6/1) -- Penn State Extension will be holding a 3-day Kiln Drying Short Course July 19-21. The ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- The ability to hold it's shape when being driven in with a mallet. On my Japanese chis ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- Rich, could you describe what you mean by driving strength? ...
Re: kiln dry vs air dried strength A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- No difference once they get to the same MC. John ...
Wet Bulb Location A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- I have an 8’x8’x20’ chamber with a DH kiln. I am looking for advice on where best to p ...
alberta spruce/pine A message posted at WOODWEB's Sawing and Drying Forum (1/1) -- is the heart wood harder to dry and set pitch or the sap wood. we will be using a scra ...
Re: Dehumidifier or AC? A message posted at WOODWEB's Sawing and Drying Forum (5/31) -- A DH is the same as an A/C from an energy point of view if you put the entire A/C uni ...
Re: End checking in mahogany panels A message posted at WOODWEB's Sawing and Drying Forum (1/31/26) -- Thanks for your reply. The weird thing is these kiln-dried boards tested at 6 to 7 ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (9/29) -- Practically all species when exposures to light, especially sunlight will turn darker ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (9/29) -- Also be aware that air dried wood is not sterilized and can have infestation issues. ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (9/28) -- The color is determined, for many species, by the humidity used and the temperature. ...
old house boiler into a kild A message posted at WOODWEB's Sawing and Drying Forum (3/28) -- My dad has an old water boiler he used to heat his house. I'm trying to get an idea o ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (1/28) -- my vote goes to air drying, more natural and carefree type of drying. ...
Re: Maintaining MC After Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (2/27) -- I should have added that the idea of lasting wrap or even in a shipping container, is ...
Re: CD bansawmill and Stanner A message posted at WOODWEB's Sawing and Drying Forum (5/26) -- What species? What green size and what final size? Kiln dried, air dried or green? Sa ...
Re: Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/26) -- The guy I use is in Vancouver, Wa. He bought almost all the inventory from others. It ...
Re: Maintaining MC After Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (2/26) -- If the package wrap is on all sides and does not have any significant holes or leaks, ...
Re: RE: Hot box to dry wood A message posted at WOODWEB's Sawing and Drying Forum (11/25) -- It sounds like your starting at a very high MC and dropping it fast....severe checki ...
Re: Solar Kiln Interior Paint A message posted at WOODWEB's Sawing and Drying Forum (9/25) -- The interior paint's main job is to absorb as close to 100% of the incoming solar as ...
Re: Solar Kiln Interior Paint A message posted at WOODWEB's Sawing and Drying Forum (9/25) -- After reading and re-reading, I think I know what to do. This product might have work ...
Re: Table Top and Skirt Shrinkage A message posted at WOODWEB's Sawing and Drying Forum (1/25) -- Your lumber is air dried apparently. This means it has not been dried enough, and it ...
Drying Redwood Lumber A message posted at WOODWEB's Sawing and Drying Forum (10/24) -- I have a customer that wants to dry Redwood Lumber. Can you tell me where I can find ...
Re: NYle Kiln L200 A message posted at WOODWEB's Sawing and Drying Forum (9/24) -- The vent kit is brand new. I've only had them for 3 weeks ...
Re: NYle Kiln L200 A message posted at WOODWEB's Sawing and Drying Forum (2/24) -- I also have purchased a L200m with power vents but haven't had it shipped yet please ...
Re: Channeled Sticker Manufacturers A message posted at WOODWEB's Sawing and Drying Forum (9/23) -- http://www.downesandreader.com/ironstick/ Do a search on "kiln stick" and t ...
Re: Dehumidification air speed A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- I forgot to mention that I am following Dry Kiln Schedules for Commercial Woods Tempe ...
Re: Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- Thank you both. Dr. Wengert's formula lines up with my estimates based on variation f ...
Re: Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/23) -- To calculate cfm, we need to assume an air velocity of 100 fpm. Then multiply the vel ...
Re: Wood Kiln Moisture Barrier A message posted at WOODWEB's Sawing and Drying Forum (2/23/22) -- Nice drawings and design. You may have to get a engineer or architect to sign off ...
Re: Solar Kiln - Fan size and other materials A message posted at WOODWEB's Sawing and Drying Forum (8/22) -- Is this for green or for air dried lumber? What will be the size of the pile of lumbe ...
Timber Frame Barn A message posted at WOODWEB's Sawing and Drying Forum (5/21) -- I'm planning to start a timber frame barn, 36 x 40 feet, four bents, three bays (24 x ...
NEKDA Spring Meeting - April 2&3 A message posted at WOODWEB's Sawing and Drying Forum (3/20) -- Our New England Kiln Drying Association Spring Meeting is April 2 & 3 in Brattleb ...
Re: Drying slab locust from a stump A message posted at WOODWEB's Sawing and Drying Forum (6/17) -- Joe When I look at your post "Drying slab locust from a stump" from 6/10 MY ...
Re: 8/4 Cherry Top moisture content? A message posted at WOODWEB's Sawing and Drying Forum (5/17) -- The outside RH in western N.Y. averages 70% RH in the summertime. It is below this du ...
Re: Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/17) -- It normally takes us about 2 weeks if we are rushing a controller order. We use Partl ...
Re: RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/16/23) -- White oak in contact with steel outside will very quickly turn the area around the ...
Re: RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/16/23) -- Galvanized will work if you don't drill a hole in it. Drill a hole and it goes bla ...
Re: Kiln drying meeting, Nov 1&2, Ohio A message posted at WOODWEB's Sawing and Drying Forum (10/15) -- Here is part of the brochure. Let me know if you want a large version. ...
Re: RF Kiln Dried White Oak A message posted at WOODWEB's Sawing and Drying Forum (6/15/23) -- The slats are going between steel supports. Want very little to no wood movement o ...
Re: Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/15) -- NYLE is one company that did have them ready to go. Lignomat used to have electronic ...
Drying A message posted at WOODWEB's Sawing and Drying Forum (12/14) -- I have a Sauna that I don't use. Could it be easily turned into a Kiln. Thank you, D ...
Re: Kiln control A message posted at WOODWEB's Sawing and Drying Forum (4/14) -- They cannot be replaced at a reasonable cost anymore. You would be better off to buy ...
Re: Hybrid Kiln A message posted at WOODWEB's Sawing and Drying Forum (1/14) -- View of solar collector ...
Re: Too Early for the Kiln A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- Dan-what you are doing is called heated room drying. It works really well in many in ...
Re: Solar Kiln from Storm Smashed Greenhouse A message posted at WOODWEB's Sawing and Drying Forum (11/13) -- We have started this morning about 6 am. I have been using my Japanese style saw to ...
2015 VT Solar Lumber Drying Course A message posted at WOODWEB's Sawing and Drying Forum (3/13) -- For those who would like to learn and share information in-person about solar lumber ...
Re: Solar Kiln from Storm Smashed Greenhouse A message posted at WOODWEB's Sawing and Drying Forum (11/12) -- You bet. You will find most of them or their concepts in the VT plans. ...
Re: Solar Kiln Question A message posted at WOODWEB's Sawing and Drying Forum (7/12) -- Glass can be the best covering material. Vandals and hail can be an issue. Avoid glas ...
Moisture level fluctuation during transportation A message posted at WOODWEB's Sawing and Drying Forum (5/12) -- My shop is located in a hot, humid town. I rent a paint booth that is located in a di ...
Hybrid Kiln A message posted at WOODWEB's Sawing and Drying Forum (1/12) -- Just sharing some info and experience on a project I undertook late last year..... ...
Re: Hybrid Kiln A message posted at WOODWEB's Sawing and Drying Forum (1/12) -- Thank you... very interesting... ...
Re: Sinker Log Process Help A message posted at WOODWEB's Sawing and Drying Forum (10/11) -- Thanks R Arely and EC I didn't realize the forum was supposed to be for professional ...
Re: Solar Kiln pile placement question A message posted at WOODWEB's Sawing and Drying Forum (2/11) -- The clearance at the bottom is for the fork lift’s forks. Without a fork lift, whatev ...
Need advice about my bookmatched quilted maple A message posted at WOODWEB's Sawing and Drying Forum (4/7) -- I acquired (on eBay) two thick slabs of quilted maple which were sawn bookmatched abou ...
Re: Exterior wood A message posted at WOODWEB's Sawing and Drying Forum (9/6) -- Do not know if available in your area.. You can now buy KDAT... it is pressure treated ...
Re: Storing KD timber outside A message posted at WOODWEB's Sawing and Drying Forum (9/6) -- We are processing roughly around 50000BF monthly spread over different thicknesses. Pa ...
Re: Augmenting Solar Kiln A message posted at WOODWEB's Sawing and Drying Forum (10/5) -- I suggest heat alone. There is no chance of increased casehardening at these low MCs. ...
NEKDA Spring Meeting - May 13-14 A message posted at WOODWEB's Sawing and Drying Forum (5/5) -- Our New England Kiln Drying Association Spring Meeting is May 13-14 in Presque Isle, M ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (1/5/22) -- I do not think that drying will change the color of the material. will it change ba ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (1/5/22) -- I am working in the painting company but i do not believe that color will change ev ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (1/5/22) -- i think it is better to sterilized it ...
Re: Thickness standard for 5/4? A message posted at WOODWEB's Sawing and Drying Forum (4/4) -- Rod, You don't need to weigh the whole log. Just take a wafer and weigh it on scale th ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (10/3) -- If I was doing museum pieces, I would definitely want sterilized lumber. ...
Re: Wood Kiln Moisture Barrier A message posted at WOODWEB's Sawing and Drying Forum (4/3) -- The sheets from large stores often cannot go over 130 F. They deteriorate at hotter te ...
Re: Wood Kiln Moisture Barrier A message posted at WOODWEB's Sawing and Drying Forum (4/3) -- In the northeast we use foam sheets available at home centers for insulating and creat ...
Re: NYle Kiln L200 A message posted at WOODWEB's Sawing and Drying Forum (10/2) -- It sounds like you have the wrong stuff or don't have it connected correctly. Call Mo ...
Re: Solar Kiln in a Humid Climate A message posted at WOODWEB's Sawing and Drying Forum (7/2) -- The humidity won't be a problem because if the raise the temp, the RH and EMC drop. Fo ...
Re: Kiln drying oak / Croatia A message posted at WOODWEB's Sawing and Drying Forum (1/2) -- Here are current drying schedules i work with. ...
Re: RE: Air Drying vs. Kiln Drying A message posted at WOODWEB's Sawing and Drying Forum (5/1/22) -- I keep a fan going on medium speed year-round in my wood drying area and i position ...
Re: Wood Kiln Moisture Barrier A message posted at WOODWEB's Sawing and Drying Forum (4/1) -- We are trying to keep the interior moisture from getting onto the insulation, where it ...