Homag KAL 310 NOT INCLUDING THE RETURN
Year of MFG 2006
Control voltage 24 V
total connected load 50A
recommended fuse 28kW
nominal current pprox.. 39A
Dust extraction
air velocity (min.)
28 m/sec (91.84 ft/sec)
air volume 4090 m3/hr (2407 cfm)
static pressure 250 mm/ws (9.84/ws)
CompressedAir
connection size Ύ
pressure required 7 bar (100 psi)
consumption / volume 705 sl/min (24.89 cfm)
Foundation requirements according to layout drawing
# 5-236-01-0360
Electrical equipment installed according to UL regulations. Voltage supplied must not fluctuate in excess of+/- 5% of its stated value. Voltage must be balanced phase-to-phase and phase-to-ground.
Note: The stated values are only applicable to the machine as specified.
Adding or deleting optional equipment may change service connection requirements.
In case ofvariations in technical specifications and capacities between the base machine and working units, the specifications and capacities given for the working units are to be considered correct.
Conditions offloor at installation site must adhere to foundation plan.
Adjustable lnfeed Fence
Homag Unit #0005
with digital mechanical counter
Pre-Milling Unit
Homag Unit #3481
HOMAG KAL 525
with two (2) motors 3 kW, 150 cycle, 9000 rpm
for max. tool diameter of 125 mm (4-15/16")
equipped with trimming column
two (2) horizontal and cross slides with spindle adjustment
electro-pneumatic horizontal jump movement of first motor
two (2) dust extraction hoods
air jet for panel cleaning
with two (2) DIA jointing heads 125 x 35 x 30 mm(4-15/16" x 1-3/8" x 1-1/8"), DKN, z = 2 x 3
max. workpiece thickness 30 mm (1-1/8")
electronic frequency inverter for control of motor speed and braking
Noise Protection Stepped
Homag Unit #0424
for pre-trimming unit
allows for inlay of long strips
centralized dust extraction port
Panel Pre-Heater
Homag Unit #2325
quartz lamp for heating substrate edge before glue application
for improved edge quality and optimum bonding
QA 34 Quick Melt Gluing Unit
Homag Unit #2123
specially designed by Ho mag - the original innovator of the quick melt syste
lower reservoir unit is designed with only seven (7) wearing parts,
which allows for ease of adjustment and reduces maintenance costs
ideally suited for quick heat-up time and color changes
one bolt secures lower unit to drive mechanism
special coupling eliminates alignment of universal drive joint
digitally displayed thermostat for both upper and lower unit, along with
heated glue roller allow for excellent control of temperature for optimum
bonding results
individual adjustment for front and rear glue gates
upper reservoir for glue granules
glue roller diameter 34 mm (1-11/32")
lower melting unit equipped with automatic control of glue level
Glue Roller Drive
Homag Unit #2141
eliminates glue charring on glue roller
lengthens pot life of glue during idle running time of machin thermostatically controlled activation I nitiates glue roller drive when lower unit reaches melting temperature while feed track is stopped
Clamping Device for Glue Pot
Homag Unit #2143
electro-pneumatic clamping of glue applicator at trailing edge of panel
ensures consistent glue line
Glue Container Back-Off
Homag Unit #2145
in case feed track stops
Multi-Purpose Magazine with Single Coil Horizontal Table
Homag Unit #2999
capable of running coiled material, strips, and solid wood bands
easily changed from one application to the next with the flip of a switch, conveniently located on the movable control pendant
infeed angle 8°
edge thickness 0.4 mm to 12 mm (0.016" to 1/2")
edge height 12 mm to 65 mm (15/32" to 2-9/16")
processing limits 900 mm2 (1.39 sq. in)
min. edge length 260 mm (10-1/4")
Clipping Unit
Homag Unit #2445
designed for today's popular use of thick coil PVC for use with single-roll table magazine
max. edge thickness 3.5 mm (0.14")
max. edge height 65 mm (2-9/16")
PVC processing limits 135 mm2 (0.19 sq in)
veneer processing limits 100 mm2 (0.15 sq in)
max. roll diameter 900 mm (35-7 /16")
Magazine Height Adjustment
Homag Unit# 2451
with threaded spindle adjustment and digital readout
adjustable +/- 5 mm(+/- 13/32")
Pressure Zone for Gluing Section Type C
Homag Unit #2507
one (1) driven pressure roller 160 mm (6-5/16") diameter
six (6) secondary pressure rollers 70 mm (2-3/4") diameter
with pneumatic pressure control for straight edges
centralized manual adjustment for edgeband thickness with digital mechanical counter
Snipping Unit HL 81
Homag Unit #3049
for straight and chamfer snipping
with two (2) motors, 0.8 kW, 200 cycle; 12,000 rpm
max. edge thickness for straight snipping 20 mm (25/32")
max. edge thickness for chamfer snipping 3 mm (1/8")
chamfer angle of 30°
edge cross section maximum of 900 mm2
max. edge height 65 mm (2-9/16")
feed speeds
panel thickness up to 40 mm (1-9/16") - 25 m/min (82 ft/min)
panel thickness up to 60 mm (2-3/8") - 20 m/min (66 ft/min)
panel gap with 20 m/min (66 ft/min) 600 mm (23-58/8") min.
with two (2) carbide tipped saws 120 mm (4-23/32") diameter; t = 30
includes electronic frequency inverter with motor braking
More info and specs on website!
