Adhesives

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

glue line creeping

6/11/13       
holly Member

I really need help...we are seeing glue line creeping in some of our dining room table tops. we can't figure out what is causing this?? it's not always on every joint sometimes only a few. they always appear after top coating. we find if re scuff it and re lacquer it they stay down but it is so frustrating. Please help!!!

6/11/13       #2: glue line creeping ...
joiner Member

What adhesive are you using?

6/11/13       #3: glue line creeping ...
Jeff Pitcher

Holly,
This is a common problem and a common misconception. The problem is the moisture content of your stock and the amount of time you allow from glue up to planing. What you're seeing is the wood shrinking around the cured glue line. You need to allow your wood to reach equilibrium moisture with its environment. Also, be sure to check the MC of your wood. It should be around 8-10%. Dr. Wengert has written several responses about this problem in the forum.

6/11/13       #4: glue line creeping ...
Holly Member

Thanks Jeff,
i have heard about the moisture content issue so i have been leaving panels clamped overnight wherever possible and a minimum of 4 hours to try to combat that. We are using Dural white glue but have seen the issue with others and the old yellow Dural as well. All of our lumber is from standard hardwood suppliers so i assume it is kiln dried to proper moisture content but maybe i should not assume. What is the proper amount of time lumber should sit in my shop for before milling and glue up? Most of our lumber is coming from the west coast by the ocean and we are in the province next door in Alberta so maybe this is causing the issue to be worse than normal? We usually let it sit for a few days wherever possible but we are a production shop and can't always do that...do i need to be leaving it sit for a week or more? how long after glue up to planning?

6/11/13       #5: glue line creeping ...
Leo G  Member

Website: http://www.lrgwood.com

Using any type of water based glue you need to give the joint ample time to be able to rid the joint of the extra moisture that it has gained because of the glue.

This means a wait time of about 3 days. Ya, you heard me - days.

I've had this problem on door panels. So now what I do is glue up, plane to thickness after it's dry which is usually a few hours. Sand with my rough grit and then let them sit for a few days. Then sand with my final grit after that.

If you can't wait that long, use a glue/epoxy that is waterless.

6/12/13       #6: glue line creeping ...
Adam Spees

I have seen some white glue joints that remain plastic(maybe this word will not offend the "creep" police) forever.

You could wait 3 days or 3 months and the glue will continue to move out of the joint after repeated sandings. It is because it is a soft drying glue.

Stay away from white glue.

Also while I'm at it. White glue is different from yellow glue. It is not simply a different color by a different brand as some people on WW seem to believe.

Franklin makes Titebond. #1 It drys rock hard and is easy to sand.
Franklin also makes a white glue. It is gummy and clogs sandpaper forever. It is known to remain plastic(creep move or whatever you want to call it).

Leo is correct with his recommendations for all glues. However, in my experience it may not make a difference if you are using a soft setting white glue.

6/12/13       #7: glue line creeping ...
Jeff Pitcher

Holly,
You might want to invest in a moisture meter to check your wood when it comes in. Depending on how you store it it could take a long time for it to reach equilibrium with your area.
Regarding the difference between white and yellow glue; there are certainly differences between formulations of PVA glue. Some are softer than others. This is not, however, a function of the color. There are plenty of softer yellow glues out there and plenty of harder white glues. There are glues such as epoxy and polyurethane that don't contain moisture. They tend to be very expensive and more difficult to work with. If you allow your stock to reach the appropriate MC and allow it to rest after gluing before you machine you will likely do away with your raised glue line issues.

6/12/13       #8: glue line creeping ...
Rich

The amount of squeeze out and what you do with it will also effect this. I wait about 10 minutes and cut off the squeeze out with a chisel. If you get big squeeze out the glue inside the joint takes longer to cure out. Titebond I rock hard? Let a string of it dry on a piece of glass. Take it off and warm it with a heat gun. It droops like a wet noodle. Epoxy or resorcinol gets rock hard. Titebond I will always give a little, especially with heat!

6/13/13       #9: glue line creeping ...
Holly Member

Thank you everyone for your responses. Leo the 3 day thing will be difficult but thats how we have to deal with maple when we use it now so i guess we will have to plan production differently. Adam the white glue thing is interesting. We used Dural yellow for years and years and were convinced by a supplier to switch to white about a year ago. I have been concerned that it always seems to remain "rubbery" or pliable but i thought maybe this would help the panels expand and contract easier with less chance of cracking. Guess I was wrong! I will be switching back to yellow for sure. And Jeff the moisture meter is something i will have to look at getting I think. This never seemed to be as much of an issue when we were using local suppliers but since we switched to a west coast supplier we have been seeing it more and more. Thank you all again and will take you up on all the advice!

6/14/13       #10: glue line creeping ...
FRANK HUTCHINSON

1. There are a number of phenomena that get described as "creep" People seem to like arguing over which qualify for use of this term. The the wood science folks enter into the discussion sporting a lab coat and PHD, however their opinions and text book knowledge are not always consistent with the way things really work.

Alot of guys who talk about this don't actually build nice things in a shop so there is a lot of really dumb info out there.

The bottom line is that "creep" can be related to the plasticity of the adhesive, or moisture introduced into the wood. From experience I have encountered and resolved problems related to both. This brings us to a couple solutions.

2. As others have pointed out it is wise to wait as long as possible after gluing up panels before final sanding. In my shop production tabletops, or door panels might get several days. A complicated lamination such a a butcher block countertop may be allowed several weeks. Quality work and furniture get several weeks.

2. Avoid using exterior PVA formulations like tightbond 2/3, unless you truly need the water resistance. For most interior woodwork they are not necessary.

I see a lot of people who are new to woodwork go for the exterior formulations
(especially tight bond 3) as the marketing buzz ("ultimate wood glue slogan") etc..." leads them to believe that it is superior.

Tightbond 1 dries rock hard in comparison.

If you want to see this for yourself, take a bottle of tightbond 1, and 3 and compare the hardness of the dried glue in the cap.

You can also use a more ridged adhesive, however this is often not practical as type 1 PVA's such as tightbond 1 are quite user friendly, and cleanup is easy.

6/14/13       #11: glue line creeping ...
Tim G

I agree with the previous points made, but the cut of the wood can make a difference as well. That is the orientation of the rings at the glue line. With flat sawn lumber
it's possible to have vertical grain next to horizontal grain, which are going to expand/contract at different rates. Might explain why some joints move more than others.

6/16/13       #12: glue line creeping ...
Adam Spees

Back in the day there was Elmers white PVA glue. It is soft and plastic when it dries. Kinda runny and does not sand well.

Then Franklin introduced an Aliphatic PVA glue called TiteBond 1. It was yellow a little thicker and a faster tack time. It dryed harder than the white and was easy to sand.

The rest is history. Franklin still makes both types. There are a ton of yellow glues of different properties.

Generally the more water resistant the softer the glue(leading to glue joint bulge). Tite Bond 3 is a soft curing glue and has obvious glue joints.

Epoxy glue joints will often show because they are wider joints and the glue is much harder than the wood.

6/18/13       #13: glue line creeping ...
Gene Wengert-WoodDoc

I agree with Jeff...the color of the adhesive is not a factor.

You can also get creep from the heat applied subsequent to gluing the panels, even if you wait three days. (The failure to wait three days will give a sunken joint...a depression at many joints.) This is a good practice, but I doubt that it is the cure for your problem.

However, from your comments it sounds like you may have a raised joint; that is why you can "scuff it and then it stays down." This raised joint is caused by the heat softening the adhesive and then the pressure on the joint (all joints are under pressure) causing the soft adhesive to squeeze out. (Creep is usually referring to a long term movement, so creep may not be the best descriptive term.) So, do you use heat at the time of finishing to cure the finish? Or perhaps you use a sander or polisher that creates heat. The gloss of the finish makes such bumps, that cannot be seen in the rough, obvious.

The cure is to change to a white or yellow adhesive that is less sensitive to heat...when it cures, a chemical reaction occurs that is not reversible. In this respect, you can try TB II. You might also consider a top quality (not the cheap ones) PUR adhesive, but it is more expensive. Perhaps Jeff can give you a specific adhesive number.

This is the voice of experience speaking, as I have worked closely with this issue with others.

6/18/13       #14: glue line creeping ...
Holly Member

Hi Everbody,
well I am a little confused as people are having different experiences with the Tightbond glues and which is best. We generally only use TB 3 when using exotics. Partly because we can only seem to find it retail and our suppliers carry Dural industrial glues. We are in Canada so I have never heard of Franklin? Dural has been used by many of us for years and I have only had problems since switching to their white. Gene i am not using heat to cure the lacquer but my belt sanders sure create heat. We are building higher end furniture and do mostly custom dining room tables so we do alot of belt sanding. I'm not sure how to source a glue that is less sensitive to heat as none of the labels talk about that kind of resistance. So you are recommending TB 2 for the heat issue? And Frank you are recommending TB 1 for the same reason? And Gene how do I avoid the heat issue? Once it has been heated does it cause the issue to happen again and again even if i let the piece sit for several hours before finishing? should I let it sit overnight and then lightly hand sand before staining and finishing?

6/18/13       #15: glue line creeping ...
GeneWengert-WoodDoc

TB 1 does not have much heat resistance. TB 3 would seem to be unnecessary for your use. You may need to clean the surfaces of some exotics to remove natural oils.

Again, consider switching to PUR, but not the cheap ones.

This heating effect will happen again and again, so use fresh sandpaper will minimal pressure at the end. Then a really light sanding at the end.

6/23/13       #16: glue line creeping ...
clarke olsen Member

Website: http://clarkeolsendesign.com

Glue-up on Friday.

6/24/13       #17: glue line creeping ...
John Eugster  Member

Website: http://www.woodworksbyjohn.com

Thought I'd weigh in on this from a desert location where my average humidity is in the single digits. I'm a small shop but have been using Gorilla Glue for glue ups and door panels and have never had a problem. Not sure how it would work out in a production shop but for me, it's the best way.

6/24/13       #18: glue line creeping ...
GeneWengert-WoodDoc

Just a reminder. PUR adhesives cure faster with more moisture. So very dry wood will be very slow, etc.

6/24/13       #19: glue line creeping ...
John Eugster  Member

Website: http://www.woodworksbyjohn.com

You're right Gene, should have mentioned that I spray one edge with water prior to glue up. Another thing I've found with the Gorilla Glue is that clean up is a breeze. I use a piece of UHMW plastic between the clamp and the wood and everything that foams out scraps, planes, or sands off without leaving any visible residue. I rarely stain so no experience there, tend to use oil, shellac, or other clear finishes only.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)