Safety Speed Cut Thermwood Corporation ECabinet Systems

Cabinetmaking

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Input on small 4 sided box, no back, no lid, in large quantities

10/2/21       
Mark B

We've been running a bunch of these small boxes, 14" wide, 2.75" deep, 6" tall. High pressure laminate exposed faces, backer on the non-exposed faces. These have to have non edge banded exterior corners (look like a mitered corner) so a standard laminate corner with routed bevel. We're running them over 1/2" veneer core and been cutting them on the CNC HPL down with a stepped rabbet at all the corners so we are left with a very small flange of just the high pressure laminate with enough extra width (1-2mm) to trim on the router table.

That small flange of laminate is of course super fragile off the machine and through assembly and a bit finicky on assembly. Trying to avoid laminating the exterior faces after assembly, cutting and handling tons of small pieces of laminate, contact, etc. and trying to stick with layed up sheets. Miter folding doesnt work well and leaves the miter seam right in the center of the bevel edge.

Wondering if anyone has any input on alternate methods or better ideas. Quantities are in the several hundreds. Ive even been wondering about something like Wilsonart Re-cover and just laying these up after assembly with peel and stick (these are not in any environment that demands contact or hot/cold pressed panels).

Id still much rather stick with the panels off the CNC if possible but keeping the corners tight can be a challenge. These arent bound to veneer core or even backer which led me to thinking of miterfolding these in MDF and then running the re-cover.

Click the link below to download the file included with this post.

woodweb.pdf

10/2/21       #2: Input on small 4 sided box, no back ...
TonyF

Mark B:

What are the colors of the laminate? Would it be possible to laminate the large face, which perhaps gets the most wear, and use Mylar, or something like it, and wrap the three sides, with just that thin film to trim off?

How much color variation is there? If it is all the same, it may be worth talking to someone and have them make you a roll of self-adhesive film to match.

TonyF

10/2/21       #3: Input on small 4 sided box, no back ...
RichC

Would miter fold work?

10/2/21       #4: Input on small 4 sided box, no back ...
Mark B

All of the exposed faces need to be HPL. Wilsonart 7518 Solar Oak.

10/3/21       #5: Input on small 4 sided box, no back ...
Tom Gardiner

Could you reinforce the laminate by applying a temporary 1/8" mdf backer cut to size when coming off the cnc? It could be taped on. Maybe that would take too long but it would cut down on the breakage and would aid in the glue-up.

10/3/21       #6: Input on small 4 sided box, no back ...
Gary

You never elaborated on why you don't think Miterfolding will work. Did you try it? True, you won't get perfect corners, they will need to be filed lightly, but you're already doing that with your current setup.

If you have high quantities like this, you may be better off with a dedicated gasketed jig, and cutting through each part, then taping them together at assembly. The trouble with a miter bit on the Router is the point has 0 speed and kind of drags along the HPL. If you can cut through say 1/8", the point is moving enough to achieve a cleaner cut.

Then again, if you have a shaper, you could create all the miters on there as well, which would be crisper.

Again, in that quantity level, you may even be better off making some dedicated assembly jigs on the CNC instead of using tape.

But if you have a TON of these, and see this type of work in your future, these would be way faster with a dedicated miter folding machine that applies the tape and cuts the fold in one pass.

10/3/21       #7: Input on small 4 sided box, no back ...
Mark B

Thanks everyone,
I somewhat discounted the miterfold for the reasons mentioned in my intial post as well as those you mention Gary. We miterfold solid surface a lot but I hog out in 2 passes prior to the miterfold on the cnc with the last one being a 1/4" spiral bull nose that reaches down to the bottom of the fold leaving only about .050" for the tip of the tool to deal with. Inserts last forever but i dont think that would be the case with laminate like you say. But I could give it a test. The option of cutting through to get into the rotation of the tool would work but then holding all those small parts, as well as handling them loose/taping after the fact, I just pretty much abandoned it for the stepped rebate. Even though were still handing individual parts the laminate is basically an onion skin till the last pass. Ive never miterfolded laminate before and I was also concerned with the possibility of squeezout under the tape being a clean up issue but thinking through this more it may be worth a try especially possibly using something like black solid surface seaming adhesive in the fold which would act as a black fill as well.

There will be a lot of these by the time they are done as I mentioned. Several hundred if not more but I dont think its going to repeat down the road and not sure there is enough in this one component of the job to justify the dedicated miterfold machinery. The stepped rebate isnt awful but it isnt great either.

Your response re the shaper has got me thinking of the miterfold but abandoning the CNC and running the two widths needed (bottom, and the face and ends) on the shaper in long lengths, back fence, and perhaps the edge beveling on the coping sled with some stops then taping them and folding them. Thinking that through as Im typing it sounds better and better and may be a lot faster than CNC miterfold or the stepped rebate.

Tom, adding the backing layer would be interesting but as you say it may add to the chaos.

Thanks a bunch for all the feedback... I get stuck in the loop all to often as Im getting older.

10/4/21       #8: Input on small 4 sided box, no back ...
Mark B

Update (I hate posts with no follow up)

Not rock solid at this point but at this point we are leaning towards VG laminate (re-cover) and just smacking together shallow rebate boxes (rebate for registration), glu/staples, flushed on shaper, and then re-cover/VG laminate, bevel trimmed on router table.

It seems like a decent option to speed up the core assembly and we can laminate 3 sides, 2 trimming stations (one straight one bevel). We will still have a bit of filling but seems like a better alternative to most other options.

Not locked yet but...

As always, thanks for the input.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
    Limtech Industries, Inc. Lamello
    Today's Sponsors

    Become a Sponsor today!