CNC

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Newbie looking for advice

3/30/19       
Chris Member

Hi

I'm very new to the CNC world. I just bought a machine and got it running yesterday. I primarily bought the machine cut profiles out of particle board, I have done a few tests and made out OK, but I'm using old bits and the old router that came with it (Porter Cable 890 2-1/4 HP) it started off OK but I might have pushed it too much and it doesn't sound to great anymore. I'd appreciate some advice on where to go from here. Keeping in mind my main concern right now is cutting parts from particle board 1/2" - 3/4" (I bought this for work and have orders to fill soon).

1. My first thought was to replace the router with the Porter Cable 7518 (3-1/4 HP). Will this hold up for what I want to do? It is a simple solution for me, just have to change the mounting plate and I'm off and running, but if you think it will burn out in a month I don't want that. If I could get a couple of years out of it that would be great.

2. When cutting particle board (not MDF) what is the best bit to use? How many flutes, up cut down cut, spiral, straight? I assume 1/4" dia or can I go 1/8"? It doesn't need to be a perfect cut but not real rough either (tried a 2 flute up cut and it was to rough for my liking...but maybe a feed speed adjustment would help?)

3. With particle board should I run the router at high or low RPM? Approximately what should the feed speed be?

4. With particle board how deep should I be cutting each pass? Is 1/4" reasonable?

Sorry if the questions seem a bit pathetic but I want to start off right with this and not regret getting into this.

Thanks for the help
Chris

3/31/19       #2: Newbie looking for advice ...
BH Davis  Member

Website: http://bhdavis.net

Chris,

Others may offer different opinions but I would suggest the following.

The Porter Cable 3-1/4 hp router is a fairly standard item on light duty CNC routers. It will be a good choice for your system.

I would use a 3/8" 2-flute carbide downcut spiral bit. This will give a clean top edge but will also compress the chips in the cut slot.

By making the cut in 2 passes at 3/8"+ each you will eliminate some most of the compressed chip issues. This could be done in a conventional cut direction. I would recommend stepping the bit 1/16" out from the final edge on the first 3/8" deep pass, then stepping it in and down on the second pass. You should be able to set this up in your CAM software.

If there is any play in your system you should also make a 3rd pass at full depth. In this case the 1st pass doesn't need to be stepped out. Instead run the 1st and 2nd partial depth passes on a climb cut, and the 3rd pass on a conventional cut. Doing this will make your part slightly oversized after the first 2 climb passes and bring it down to correct size on that 3rd conventional pass. Do this type of cut arrangement if you find your parts are coming out slightly small with the 2-pass system.

Lots of good bit manufacturers out there. Don't cheap out with an import bit to save money. Expect to spend about $40+ per name brand bit.

BH Davis

3/31/19       #3: Newbie looking for advice ...
james e mcgrew  Member

Website: mcgrewwoodwork.com

BH said what I think you needed to hear, The 7518 is an industry workhorse as the bushings and bearings can be replaced.

We have a tool store here who repairs them if you get a new 7518 have the old one looked at, having an extra anything can prevent a slow down in work !

3/31/19       #4: Newbie looking for advice ...
Chris Member

Hi Guys

Thanks for your input it is very helpfull. When BH says light duty CNC. I do want to use this for a few hours a few days a week or more. Is the Porter Cable good for this? Or should I be leaning towards a 2.2kw spindle?

3/31/19       #5: Newbie looking for advice ...
BH Davis  Member

Light duty means other than the heavy iron machines. Perhaps a poor choice of words on my part. If you were running 8 hours a day / 7 days a week you might want a more substantial machine. However since you didn't say what machine you had it left me to speculate it was not a heavy iron router. Plus larger and heavier machines typically would come with 10 hp plus tool changing spindles as vs. a 2 hp Porter Cable router.

The Porter Cable router will be fine for what you will be doing. I wouldn't worry about running it several hours a day 5 days a week. Beyond that a spindle might be in order. As James said though the router bearings can always be replaced.

BH Davis

4/1/19       #6: Newbie looking for advice ...
Mark B Member

Tossing up a photo or giving some more detail on the actual machine/frame/construction would probably give people more info to guide your decision. The decision to move to a spindle over a router motor seems about a no brainer for many today. While the 7518 will give you some speed control the spindle would give you full control though it may not be a simple swap out so if you need to maintain production the 7518 is probably the best choice for now.

I wouldnt personally go below 1/4" for the particle board in my opinion but your machines capability with regards to feed speed will have a lot to do with how hard you can push the tool.

Do some googling on chipload per flute for various cutters and you can quickly get some ideas of rough starting points for feeds and speeds. After that you can dial up your feed until you see/hear bad juju or break a tool and then back down.

4/1/19       #7: Newbie looking for advice ...
Chris DeVries

Thanks again for everyone's input. The machine is a 5x10 MechMate. I have attached a few pics. Even though sticking with a porter cable would be easiest I think I'm leaning towards a 2.2kw 3 hp spindle...unless that sounds crazy.

My understanding is that the hp on the spindle is a more continuous rating compared to the router.


View higher quality, full size image (2016 X 1512)


View higher quality, full size image (2016 X 1512)

4/3/19       #8: Newbie looking for advice ...
ryan

If it were me I would buy the spindle. You will be able to run the machine harder and turn out parts quicker. The faster you can make your parts then you can be doing something else. In the end you make more money and paying the extra for the spindle easily takes care of itself. There is a lot of difference in a 3hp router and a 3hp spindle. As was said earlier heavy duty machines are heavy duty. Our CNC weights in at over 7,000 pounds.

4/3/19       #9: Newbie looking for advice ...
james e mcgrew  Member

Website: mcgrewwoodwork.com

I have not seen a mech mate in a few years, got the plans and almost built one a decade ago, Lots of South Africans built them !

4/4/19       #10: Newbie looking for advice ...
Larry

The big PC router is probably one of the better hand held routers on the market. The problem is they are not made for continuous running. The brushes wear pretty fast.
The tooling companies have feed and speed charts on their web sites to get the correct chip load. If you buy a regular spindle will you have the ability to vary RPM's? If your control doesn't have that ability you can buy VFD's from China pretty cheap.

An easy way to check see if your chip load is reasonable is to (carefully) take hold take hold of the bit right after cutting a sheet. If you burn your hand your chip load was too little. Increase feed speed or reduce RPM's. If your horse power won't permit fast enough feeds you will have to make multiple passes.
Buy high quality bits. They are worth their price. We use Onsurd marathon 3/8", 2 flute compression spirals, 12hp spindle. Always use the shortest bit that will do the job.


Post a Response
  • Notify me of responses to this thread
  • Subscribe to email updates on this Forum
  • To receive email notification of additions to this forum thread,
    enter your name and email address, and then click the
    "Keep Me Posted" button below.

    Please Note: If you have posted a message or response,
    do not submit this request ... you are already signed up
    to receive notification!

    Your Name:
    E-Mail Address:
    Enter the correct numbers into the field below:
     

    Date of your Birth:



    Return to top of page

    Buy & Sell Exchanges | Forums | Galleries | Site Map

    FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)
    Suction Cups, Vacuum Lifters, Vacuum Pumps from Anver Corporation ecabinet systems.com Thermwood Limtech Industries, Inc.