Cabinet and Millwork Installation

You are not logged in. [ Login ] Why log in
(NOTE: Login is not required to post)

Post a Response
The staff at WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at any WOODWEB Forum. Participants should undertake the use of machinery, materials and methods discussed after considerate evaluation, and at their own risk.
Your Name:
Your Website:
Email Address:
Subject: Re: Installing loose back splashes

Message:

(read message guidelines).
Note: Do not use the below fields to advertise your business - only for links related to the discussion.
Thread Related Link URL:
Thread Related Link Title:
  To "point" to an image (picture) from another website, provide the URL (Web Address) of the file ( include ONE reference to http:// )
Thread Related Image URL:

Date of your Birth:

Upload a Thread Related File:
File Types: Image (gif-jpg-png-bmp), PDF, Sketchup, Video (mov avi wmv mpeg mpg mp4 ogg). (Image Upload Tips)

I have read the Site User Agreement and agree with the Terms

  <= Check to receive e-mail notification of responses

Message Thread:

Installing loose back splashes

5/25/16       
Rob Long  Member

Im just curious how you install loose plastic laminate back splashes? The way we do it now is quite time consuming and yields mixed results ( clamp the front edge of the top, and cut sticks to keep pressure on the splash against the wall glued with silicone). We have used the back splash clips that screw onto the c-top and route into the splash but that seems to take quite a bit of time with good results.

I would love to hear from you.

5/25/16       #2: Installing loose back splashes ...
Gary B.

Rob,

I don't install anymore, but the coolest trick I saw for this was Silicone and a professional hot melt glue gun. apply both, then push it tight while the hot melt cured, then that would hold while the silicone dried.

5/25/16       #3: Installing loose back splashes ...
keith

Website: http://hightechcabinets.com

best way we discovered is to place backsplash in place and note recesses in wall. install a screw into wall stud or install sheetrock anchor into sheet rock behind backsplash where the backsplash is out from wall located in the middle area of the backsplash. now that you have a few screws installed mark locations on back splash at corresponding locations of screws and use a keyhole bit to router screw location in back of splashes starting at the bottom of backsplash moving up to accomondate the screw that's in the wall. key hole slot allows for splash to be slid down over screw heads that you have already installed in wall. to achieve tight fit just adjust screws to desired depth sticking out from wall. trial and error sometimes on screw depth , but once you've tried the system you'll really like how it works. no glue , no clamps, no headaches no redo's no etc....

5/26/16       #4: Installing loose back splashes ...
Tom G

Website: http://tpgcabs.com

I've been using smartclips for over 20 years. http://thesmartclip.com/ They work really well.

Smartclips

5/26/16       #5: Installing loose back splashes ...
Scott

Smart clips are best that we have tried. Keeps the back splash fastened to the counter top so there is no separation later on.

6/2/16       #6: Installing loose back splashes ...
David Werkheiser  Member

When you glue the splashes to the wall and the cabinets and attached top settle, the caulk joint opens with the splashes left hanging on the wall.
Smart clips work well, the flake is routed out from the bottom with just the laminate left, if the caulk joint ever fails the splash is not going to swell from water. The clips also let your splashes fit to a curved wall with out clamps.
I will agree, Smart clips are time consuming the use.

6/2/16       #7: Installing loose back splashes ...
Pat Gilbert

Why would you leave them loose?

I have always either had them formed with a coving machine or set the splashes in the shop with caulk and screws.

The splash is then scribed to the wall.

FWIW that is the 2 ways everyone around here does it.

6/6/16       #8: Installing loose back splashes ...
Joel

COnst Adhesive with a decent hot melt glue gun is the only sane way to attach lots of commercial backsplashes. Done 100's this way and the only time it doesn't work well is if the wall is way cupped. Do yourself a favor and get a commercial glue gun. The glue gets hotter and gives you a few more seconds to position. Probably holds better too.

6/16/16       #9: Installing loose back splashes ...
Pat Gilbert

Everyone in So Calif is insane?

Hmm may be some truth to that.

6/20/16       #10: Installing loose back splashes ...
Rob Long  Member

Thanks, We are doing many splashes at once. Seems to me like the Hot Melt Glue with a commercial applicator is the fastest way to install these splashes. When youre installing 50-100 of these at a time this seems the best option. If im charging my customer by the hour this seems best for everyone involved.
Next time I will try the hot melt glue option and report back. Thanks

6/20/16       #11: Installing loose back splashes ...
Pat Gilbert

If you are setup the coving is the fastest and best.

Shops out here used to do it this way exclusively as in hundreds of apartments at a time.

Apparently we are on different planets?

6/20/16       #12: Installing loose back splashes ...
Gary B.

Pat,

I saw this technique with commercial installers, in schools, hospitals, office buildings, etc. It did work very well, and allowed everything to flat stack to the site.

 

Buy & Sell Exchanges | Forums | Galleries | Site Map

FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB's Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • "Cross posting" is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed - Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB's Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB's discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB's Systems Administrator
    (return to top).

    Carefully review your message before clicking on the "Send Message" button - you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB's forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).

    Repeated Forum Abuse: Forum participants who repeatedly fail to follow WOODWEB's Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)


  • Forum Posting Help
    Your Name The name you enter in this field will be the name that appears with your post or response (return to form).
    Your Website Personal or business website links must point to the author's website. Inappropriate links will be removed without notice, and at WOODWEB's sole discretion. WOODWEB reserves the right to delete any messages with links it deems inappropriate. (return to form)
    E-Mail Address Your e-mail address will not be publicly viewable. Forum participants will be able to contact you using a contact link (included with your post) that is substituted for your actual address. You must include a valid email address in this field. (return to form)
    Subject Subject may be edited for length and clarity. Subject lines should provide an indication of the content of your post. (return to form)
    Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
    Thread Related File Uploads Thread Related Files posted at WOODWEB's Forums and Exchanges should provide supporting information for the topic being discussed in the current message thread. Video Files: acceptable video formats are: .MOV .AVI .WMV .MPEG .MPG .MP4 (Image Upload Tips)   If you encounter any difficulty when uploading video files, E-mail WOODWEB for assistance. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related File that contains inappropriate content will be removed, and uploaded files that are not directly related to the message thread will be removed. WOODWEB reserves the right to delete any messages with links, files, or images it deems inappropriate. (return to form)